Search results for query: *

Knock came on my door and it was a brand new Holley, my Cindy kept hearing that i wanted a 650 vs .she said its time i got a new one what a keeper.my thing is it is a 650 vc 4150, duel feed,on the horn the list number is not what i have seen befor. its 0-80783c got me wondering if and when how...

I am in need from the brake masters hear.I want a bigger cam for my 360, the 262 comp is leaving some on the table.the thing is I have PDB,so a bigger cam is going to give low vacuum, i know very little of the vacuum can.so what do i need to change over from PDB to MDB CAR.THANKS A TON.I have 11...

Looking for a camshaft, my build with about 1000 miles.360 30 over 9 two to 1 pistons, 340 j heads 202 valve, edelbrock rpm performer, headers, 600 holley, stock convertor,323 sure-grip.my cam now is the comp 262, witch me and my engine builder say is small, also i have power brakes.my last 69...

had my gas pedal fall apart yesterday the pin fell out.i need help on how to install the spring witch way thanks i am pulling my hair out lol.

Hi guys going to run a #8 wire form alt to relay, but haveing a hard time finding a #12 wire link, part guys are no help or i am just dumb.could someone show a pic of said link and maybe a part number, i live in canada .thanks.

looking to up grade from my stock coil too something better.what will work with my stock electronic ing , share your thought tanks.

Good day all, my 71 has a 65 amp ALT with the 2 wire.we went for a drive last night. once it got dark and i turned on my lights all is fine until i get stop at a light all lights dim the alternator starts to discharge and the car stalls, bummer.the idle is set at 800 rpm in D.what is causing...

Was there a Plymouth trunk emblem? on my 71, if so pictures would show me where. many thanks.

I have ordered a EQUUS temperature gauge, but a few car guys said they are junk dont read right, so what are your thoughts , what are you using,bear in mind money is tight.

I have a rebuilt 360 with about 500 miles on her.9-1 30 over speed pro pistons, 3 row rad with shroud, 170 stat, a/c water pump, my car is no longer an a/c car.pull the cap good flow at idle.7 blade clutch fan.my problem is when we are cruising around the temp goes to half way on my factory...

Are the rear emergency brake cables the same length on my 71 Satellite.

71 Satellite 904 tranny I have the 8 3/4 ready to go in, now going from a 8 1/4 to 8 3/4 what are the chances i will not have to cut the drive shaft? with the 8 1/4 now i have only about an inch i can push into the tranny to remove the drive shaft.My fear is when i do the change over and have to...

I like Joe Gibbs but its has bin a few years so i don't know what weight to get, its for my new 360, and it will be fired up March or April if it matters.Happy new year to you all.

i have 11'' rear brake, just got 2 used brake shoe guide plates, mu question is should they be flat like all outhers i have work on, the 2 i have now are booth bent.could you clear this up ps MERRY X MASSSSS TO UUUUUUUUUUUUUUUUUUUUUUUUU.

hey guys is the right front brake line 5 1/6 if it matters it is disk brake, i have to scramble to get it, we in ontario canada are going throw a lock down again. thanks.

Has anyone had a new trans mount, that the big factory bolt will not go in.2 years ago i bought 1 and my bolt would no go in so i used the old 1.now its time for the new 1 any thoughts.

need a picture of the rear brake set up of 11'2 1/2 i almost have all the parts,never had 11'drums befor so a pic of how it all goes together.the nice thing is i got the finned drums that have been turned.thanks.

on my 8 3/4 witch gasket goes between the tube and backing plate.i have a foam 1 and a steel 1 .thanks gang.

for canadians only. wanted a 489 case with 323 or 355 gear with sure grip.

Doing my home work, when i order my axle bearings do i get the bearing, outer seal, and collar all, 2010 was the last time i work on a 8 3/4 rear so my mined is not what it used to be. I have the inner seal in no thanks.