• When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.

Welding help please. Can't get the machine to start up.

Status
Not open for further replies.
There is a switch up above that changes it from a spool gun to the regular feed. Not a crappy welder just bad luck. Not everyone can afford a 2000 dollar setup.

IMG_1579[1].JPG IMG_1580[1].JPG
 
In 86 I traded a motorcycle for a Millermatic 200, some tools and a bunch of steel. Still have the machine and still like it. Got a Lincoln 100 years ago just for the portability and well, that one didn't stick around for long.
 
I always thought that Lincoln was a good quality welder. Sounds like you got a bad one if you followed the setup instruction to the tee. I'd simply return it.

I bought a similar Century MIG unit since I don't do much welding, but wanted the ability to weld when I need it. Never had a problem with it. I suspect it has the capability to weld better than I can.
 
Sorry if I come off as a dick with some of my comments. But I like to think reasonable and practical and for practical purposes most people can afford a lower cost welder that they may or may not use more than that ONE time they needed it. Harbor freight 90 amp 99.00 welder was a pile of ****. But it did what it needed to do. The welds looked like ***/the welder guy can't weld for ****. But with even the worst welds a grinder can make it pretty. :BangHead:
 
Last edited:
Don't some rental places rent welders?


I waited and saved and worked my tail off to buy a really good welder. Not trying to put anyone down for not being able to afford a bigger welder.
 
Last edited:
Not sure if Lincoln has a cheaper version that they sell to the box stores, but I have a 180 dual voltage that I just love. I bought it from a welding supply house though. Actually traded in my Millermatic which I hated on it.
 
Don't some rental places rent welders?


I waited and saved and worked my tail off to buy a really good welder. Not trying to put anyone down for not being able to afford a bigger welder.
Miller bobcat welder around 150 a day, I suspect a mig would be cheaper
 
Checked 15 years ago, $60 a day for a Miller mig .
110v or 220v? Amp? Might not be a bad option if you can prep a bunch of welds (screw panels temporarily) and go get the welder for half a day.
 
I'm sure a grinder will be necessary after I'm done. I spoke with Lowe's today and was told.it has been longer than 30 days so they can't do anything. I'll start going over their head tomorrow to remedy the situation. Yeah Beep, I checked that switch too.
 
Not even a spark? Two machines? Hmmmm. A bad run?

FWIW, My Hobart only does 115 on certain machine settings (4 thru 7)...........

upload_2018-2-25_12-9-24.png
 
I figured with two I had to be the problem. I'll run through it all again this afternoon to check it all again.
 
I figured with two I had to be the problem. I'll run through it all again this afternoon to check it all again.
I bought a flux core welder from Home Depot a few years back it was a simple set up, not much you can mess up. I’d blame the machine
 
I figured with two I had to be the problem. I'll run through it all again this afternoon to check it all again.
Probably have to ship it to Lincoln. Maybe you can talk them in to an upgrade for a few bucks.
 
I figured with two I had to be the problem. I'll run through it all again this afternoon to check it all again.

I see near the end of this video there is a white reset button on the back. Give that a push if you haven't already tried. Also watch the video and compare what you see to yours.



When you squeeze your trigger, you should hear a good solid click. That sound is the contacts coming together to complete the circuit for the arc. Hopefully you find something simple.
 
I own a Miller 252, a Thermal-Arc inverter tig and an Eastwood 135 mig.

I weld A LOT. I can tell you for a fact that the Eastwood welds .023 and .030 thin gauge as good as the Miller.

So don't let cost or name or input voltage fool you. An inexpensive welder, set up properly and with practice can produce nice welds.

There are some VERY important things to consider with mig though ...
1) welding clean metal is important
2) welding with clean wire is VERY important. If you're an "occasional" welder, remove the wire when you're done and store it in a ziploc bag or container so it doesn't rust. Rusty wire will produce shitty welds and will gum up the liner and roller wheels and result in poor conductivity, feed, etc.
3) Use a "mix" gas - pure CO2 will result in a lot of spatter. Pure argon is for tig - not mig.
4) Practice, practice, practice.
5) Watch "weldingtipsandtricks" videos or others. There is a wealth of info on YouTube.
 
Sorry if I come off as a dick with some of my comments. But I like to think reasonable and practical and for practical purposes most people can afford a lower cost welder that they may or may not use more than that ONE time they needed it. Harbor freight 90 amp 99.00 welder was a pile of ****. But it did what it needed to do. The welds looked like ***/the welder guy can't weld for ****. But with even the worst welds a grinder can make it pretty. :BangHead:
Clipboard01.jpg
 
Status
Not open for further replies.
Auto Transport Service
Back
Top