Pro Flo 4. Edelbrock

Grabinov911 · Feb 10, 2019

Here are photos comparable to yours (dropped-base air cleaner on). I'd call it 9 3/4" or 9 7/8". It's probably slightly less given the angle of the tape required by the air cleaner.

This matches your photo (page 6) almost EXACTLY. It should. Same block and intake manifold with 4150 carbs (your Demon to my Quick Fuel). The question is, how much higher is it after the Pro Flo swap?

Dennis H · Feb 10, 2019

Here is one with the Edelbrock RPM Performer and 850 Demon still on. Will do tomorrow.
Go to edelbrockforums for info too. There are edelbrock staff there for questions. Not just customer service, they are techs and well informed.

Dennis H · Feb 10, 2019

https://forums.edelbrock.com/forum/pro-flo-efi/pro-flo-4

Dennis H · Feb 10, 2019

From Valley Pan Center.

CoronetDarter · Feb 11, 2019

Edelbrock is pumping up their Pro Flow marketing campaign. Going after the Holley Sniper. In the blog it states that Eddy stopped making TBI units in 2017.
https://www.edelbrock.com/eliminate...ampaign=Ecomm-PF4-Bronco-V27&utm_medium=email

themechanic · Feb 11, 2019

Dennis, did you join the chrome dome club?

Dennis H · Feb 11, 2019

Not me. Not yet.

themechanic · Feb 11, 2019

Dennis H said:
Not me. Not yet.

That guy must have been your mechanic?

Dennis H · Feb 11, 2019

My pal John. Mopar guy.

themechanic · Feb 11, 2019

Dennis H said:
My pal John. Mopar guy.

Some of us are more streamlined than others.

ckessel · Feb 12, 2019

And think of the energy saved by not using a blow dryer! More power available for the neighbor's hybrid/electric car. Win win!

tmaleck · Mar 25, 2019

Dennis,
I've been meaning to ask, where did you put the coolant temp sensor for the FI system?
Tim

Dennis H · Mar 25, 2019

Tech says water pump area.

Derwud · Mar 26, 2019

Dennis H said:
Tech says water pump area.

Most of the Aluminum Water pump housings have 2 spots for a temp sensor.

andyf · Mar 26, 2019

tmaleck said:
Dennis,
I've been meaning to ask, where did you put the coolant temp sensor for the FI system?
Tim

I started to make thermostat spacers with a place for the EFI temp sensor after running into this problem on my car. You can now buy them from Hughes Engines.
http://arengineering.com/products/thermostat-spacer-with-efi-sensor-port/

1967coronet440 · Mar 26, 2019

andyf said:
I started to make thermostat spacers with a place for the EFI temp sensor after running into this problem on my car. You can now buy them from Hughes Engines.
http://arengineering.com/products/thermostat-spacer-with-efi-sensor-port/

That Looks like a nice piece, I may grab one for my sniper 4500 set up.

Derwud · Mar 26, 2019

My only issue with that is, it would not get a warm up temp. Just go from warm to hot as thermostat opened.

5.7 hemi · Mar 26, 2019

The sensor is below the t-stat, so you’d be fine.

Derwud · Mar 26, 2019

Had one on my car. did not work great for a cooling fan sensor.

andyf · Mar 26, 2019

1967coronet440 said:
That Looks like a nice piece, I may grab one for my sniper 4500 set up.

It worked great with my Sniper setup. You just have to make sure you get a good temp sensor. Some of the temp sensors that Holley ships read low. I found out that you need to test the sensor before you install it. You can test them with a volt meter by reading the resistance.

Pro Flo 4. Edelbrock

Well-Known Member

FBBO Gold Member

FBBO Gold Member

FBBO Gold Member

FBBO Gold Member

Oklahoma is OK

FBBO Gold Member

Oklahoma is OK

FBBO Gold Member

Oklahoma is OK

Well-Known Member

Well-Known Member

FBBO Gold Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

FBBO Gold Member

Well-Known Member

Well-Known Member

Similar threads