• When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.

How’s this for timing chain slop

Haha, no you should replace it. Double roller.
 
I've seen worse with that type of chain.....
 
Ya, that's pretty normal for anything with more than a few thousand miles. Since you're in there, put a new quality double roller set in. I'd degree it just to make sure you know what you've got.
 
I'd check what the cam is set at now then go from there. If it felt a bit on the sluggish side but was tuned well.....you might think about advancing it a couple of degrees or so. A cam that's advanced a bit brings in the torque at a lower rpm but you also need to make sure you have good valve to piston clearance. If it was running good before....leave it timed in the same spot but you will need to determine what that spot 'was' :D Not that hard to do though.
 
Measure your cam to crank center distance. If it's undersize from line honing like mine, you'll
need a -0.005 or -0.010 under setup. I just bought the last cloyes double roller in the world
from Jeg's. I bought & put a new stock one on and had to buy a -0.005 under set. FSM says
3/16" is max.
Good luck finding a single bolt set!
 
zyzzyx said:
Measure your cam to crank center distance. If it's undersize from line honing like mine, you'll
need a -0.005 or -0.010 under setup. I just bought the last cloyes double roller in the world
from Jeg's. I bought & put a new stock one on and had to buy a -0.005 under set. FSM says
3/16" is max.
Good luck finding a single bolt set!
Click to expand...

Yeah, 3/16 of rotation of the cam gear.... Measured at the outer edge of the cam sprocket... I'll bet if you measure that it'll be less than half the allowable slop.... Not saying I agree, just stating what the factory service manual says..... Which is always the point to source for accurate information...

Screen Shot 2022-03-08 at 5.32.58 PM.png
 
66Satellite47 said:
Ya, that's pretty normal for anything with more than a few thousand miles. Since you're in there, put a new quality double roller set in. I'd degree it just to make sure you know what you've got.
Click to expand...
So I am an idiot, I changed the single to a double, put it all back together and then realized i forgot this thing. What is it and do I need to take it all back apart?

image.jpg
 
That is an oil slinger, It's supposed to reduce the likelihood of oil leaking from the from seal & it's supposed to improve lubrication of the timing chain... Not all engines had it originally so some folks intentionally delete it & others are religious about it needing to be in place...
 
1 Wild R/T said:
That is an oil slinger, It's supposed to reduce the likelihood of oil leaking from the from seal & it's supposed to improve lubrication of the timing chain... Not all engines had it originally so some folks intentionally delete it & others are religious about it needing to be in place...
Click to expand...
64fury74charger said:
Oil slinger that helps keep oil from going out the front crank seal. That’s an important part.
:BangHead: :thumbsup:
Click to expand...
Yep and yep. It is but can be left out without issues.
 
You must log in or register to reply here.

Similar threads

hemi71x
  • Locked
SOLD TIMING COVERS. Big Block Engines. & Roller Timing Chain & Gear Set.
Replies
2
Views
650
hemi71x
hemi71x
496coronet
Need help identifying original Mopar rear brake drum 2405798
Replies
4
Views
575
496coronet
496coronet
boboh1
Will This Endcap Still Work With New Type of Seal?
Replies
8
Views
626
BeepBeepRR
BeepBeepRR
C
Your thoughts on this oil leak
Replies
11
Views
916
1 Wild R/T
1 Wild R/T
E
383 plastic on timing sprocket damaged
Replies
5
Views
458
Geoff 2
G
Auto Transport Service
Back
Top