/ Register

Search Results

Search Again
Page 1 of 4
  1. Bee1971
    Post

    AR Engineering Valley Pan shape (?)

    With the AR Engineering plate , he recommends using his bat wings for sealing the intake manifoldDon’t you still have to seal or rtv a bead of...
    Post by: Bee1971, May 8, 2022 in forum: Fuel and Air Systems
  2. Bee1971
    Post

    440 still idles with screws turned in

    My head is spinning counter clockwise like the Distributor in this thread
    Post by: Bee1971, Apr 4, 2022 in forum: Fuel and Air Systems
  3. Bee1971
    Post

    1969 GTX stock Intake - Carburetor Stud Threads?

    I would definetly block it with your valley pan running that carb you mentionedHonestly depending on hood clearance , I would run a thicker...
    Post by: Bee1971, Apr 4, 2022 in forum: Fuel and Air Systems
  4. Bee1971
    Post

    1969 GTX stock Intake - Carburetor Stud Threads?

    With the factory intake you said you where installingYou going to run the heated crossover on the intake manifold or block it ?
    Post by: Bee1971, Apr 4, 2022 in forum: Fuel and Air Systems
  5. Bee1971
    Post

    1969 GTX stock Intake - Carburetor Stud Threads?

    NoFactory also used Carb Bolts , not studshttps://www.megapartsusa.com/proddetail.php?prod=110-FCB8055Pretty sure the 68/69 Models used a...
    Post by: Bee1971, Apr 4, 2022 in forum: Fuel and Air Systems
  6. Bee1971
    Post

    AFB accel pump

    I would bee looking at the Edelbrock 1467 or 1468 Accelerator Pump1468 has a stiffer spring
    Post by: Bee1971, Apr 2, 2022 in forum: Fuel and Air Systems
  7. Bee1971
    Post

    AFB accel pump

    Leather - Carter AFB #4294At least you can use for dimensions to look thru https://www.carburetor-parts.com/pump-ap213.html...
    Post by: Bee1971, Apr 2, 2022 in forum: Fuel and Air Systems
  8. Bee1971
    Post

    Edelbrock Carb ID

    AVS Top - Edelbrock Thunder Series - Black linkageFlip it over so we can see the bottom base plate throttle blades for size
    Post by: Bee1971, Apr 1, 2022 in forum: Fuel and Air Systems
  9. Bee1971
    Post

    440 still idles with screws turned in

    Mopar 284/484 CamYour doing good with 6"-8" of vacuum at idle with that cam and 700 RPMs at idle And it’s probably bouncing aroundYou said...
    Post by: Bee1971, Mar 29, 2022 in forum: Fuel and Air Systems
  10. Bee1971
    Post

    Fuel Pressure Gauge On 440 Six Pack?

    I just gorilla taped the fuel pressure gauge to the OUTSIDE of the windshield so I could see it in front of my faceMy motor was shutting down at...
    Post by: Bee1971, Feb 18, 2022 in forum: Fuel and Air Systems
  11. Bee1971
    Post

    When to drill holes in the throttle plates?

    383 - AutoSame Comp Cam XE275 HL - Same Heads - 16 initial / 34 totalAVS - 2 800 cfm - Same 13" vacuum at idle , bounces around a littleIdle...
    Post by: Bee1971, Feb 17, 2022 in forum: Fuel and Air Systems
  12. Bee1971
    Post

    Quality Carburetor?

    Both electric and manual says Ships Monday - 1906/1905Same with Summit Ships tomorrow...
    Post by: Bee1971, Jan 2, 2022 in forum: Fuel and Air Systems
  13. Bee1971
    Post

    2 piece fuel line to Carb.

    [ATTACH] [ATTACH]1971 383 Factory Holley CarbYepper In between the heater hoseshttps://www.inlinetube.com/products/dbe6808
    Post by: Bee1971, Oct 27, 2021 in forum: Fuel and Air Systems
  14. Bee1971
    Post

    2 piece fuel line to Carb.

    Carter AVS - 1971 383 https://www.inlinetube.com/products/dbe6806This is routed behind the heater hosesConnects to the fuel filter next to...
    Post by: Bee1971, Oct 27, 2021 in forum: Fuel and Air Systems
  15. Bee1971
    Post

    DP4B and throttle/kick down bracket

    About five years agoOn my Weiand Dual Plane , had the same issueBracket fit fine with the Edelbrock PerformerAnywaysAt the time I dont...
    Post by: Bee1971, Oct 25, 2021 in forum: Fuel and Air Systems
  16. Bee1971
    Post

    Fuel Lines, tank pump to Carburetor

    1971 Charger 383 was two steel fuel lines at 5/16"I would assume your talking fuel line from gas tank towards fuel pumpAnd then fuel pump to carb
    Post by: Bee1971, Oct 16, 2021 in forum: Fuel and Air Systems
  17. Bee1971
    Post

    New or Rebuilt Carter AVS 4966S

    1971 Carter AVS 4966s came on the NON HP 440 If you where to flip it over , you will notice it has the smaller primary boresAround 630 cfm...
    Post by: Bee1971, Oct 11, 2021 in forum: Fuel and Air Systems
  18. Bee1971
    Post

    Edelbrock Fuel Line Question?

    With a factory Carter AVS steel fuel linehttps://www.inlinetube.com/products/dbe6805
    Post by: Bee1971, Oct 9, 2021 in forum: Fuel and Air Systems
  19. Bee1971
    Post

    Edelbrock issue or set up not right?

    Check FAST idle screw depending upon choke setting - Not your regular idle screwHesitation could bee as simple as an adjustment for secondary...
    Post by: Bee1971, Oct 2, 2021 in forum: Fuel and Air Systems
  20. Bee1971
    Post

    RPM intake with Trick flow heads

    AR Engineering makes valley plates like thatThen you use his bat wings to seal the valley plate with the headsAnd like mentioned , grind...
    Post by: Bee1971, Aug 17, 2021 in forum: Fuel and Air Systems
Showing results 1 to 20 of 74 Next >
Search Again
Page 1 of 4
Welcome to our site! Please take a moment and Register today!
  1. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.
    Accept Learn More...