Search Results

Search Again

Page 1 of 4

Post
10” Drill Press, What is a good one?
Buy a used Bridgeport mill.
Post by: toolmanmike, May 23, 2022 at 8:26 PM in forum: Shop, Garage and Tools
Post
10” Drill Press, What is a good one?
Delta
Post by: toolmanmike, May 23, 2022 at 8:26 PM in forum: Shop, Garage and Tools
Post
Propane Torch?
That's what she said! :rofl:
Post by: toolmanmike, Apr 19, 2022 in forum: Shop, Garage and Tools
Post
air compressor recommendation
Rewire your garage with 220 power. Compressor wise I always recommended: 220 volt and a minimum of 5 horse/60 gallon, 2 cylinder, 2 stage, with a...
Post by: toolmanmike, Mar 8, 2022 in forum: Shop, Garage and Tools
Post
Sheet metal tool recommendations.....
Overkill for bending little patch pieces. Nice old brake though.
Post by: toolmanmike, Feb 7, 2022 in forum: Shop, Garage and Tools
Post
Sheet metal tool recommendations.....
Before you buy a hammer, watch this guy's videos. He does more with a welder, hammer, a piece of pipe, and a 2x4 than most can with a shop full of...
Post by: toolmanmike, Feb 7, 2022 in forum: Shop, Garage and Tools
Post
Rotisserie In Georgia
Start a wanted thread.
Post by: toolmanmike, Jan 28, 2022 in forum: Shop, Garage and Tools
Post
SAE tap & die set
Is that what you wanted to do? Chase threads? Clean and straighten?
Post by: toolmanmike, Jan 10, 2022 in forum: Shop, Garage and Tools
Post
SAE tap & die set
Not a tap and dye but just a thread chaser set. One cuts new threads and the chaser just cleans and straightens threads. DH didn't say what he...
Post by: toolmanmike, Jan 10, 2022 in forum: Shop, Garage and Tools
Post
Propane Torch?
Yep I have a mapp with a hose. Damn handy for plumbing. I love sweat soldering copper.
Post by: toolmanmike, Dec 20, 2021 in forum: Shop, Garage and Tools
Post
Propane Torch?
I have one with a hose and one without. I prefer the one with a hose best.
Post by: toolmanmike, Dec 20, 2021 in forum: Shop, Garage and Tools
Post
DIY under hood LED bar light
It all costs more now days. Synthetic oil and $100+ labor rates are the cause. At $1.66/min a 20 min. oil change will run you $33.20 for labor...
Post by: toolmanmike, Dec 11, 2021 in forum: Shop, Garage and Tools
Post
What kind of pliers do I need for this clamp?
Nippers are designed to cut. They will squeeze the tabs closed but if you don't smash down the top it won't hold. The proper tool will squeeze the...
Post by: toolmanmike, Nov 25, 2021 in forum: Shop, Garage and Tools
Post
Newest shop toy
Solid! Look at the history of that vise. http://vintagemachinery.org/mfgindex/detail.aspx?id=11524
Post by: toolmanmike, Aug 30, 2021 in forum: Shop, Garage and Tools
Post
Continuity tester with a difference
Back probe only. A poke in the insulation and the slightest bit of moisture and corrosion changes the continuity and can mess with anything...
Post by: toolmanmike, Aug 14, 2021 in forum: Shop, Garage and Tools
Post
Harbor freight towable backhoe review.
I would sure dig seeing a video! :lol:
Post by: toolmanmike, Aug 2, 2021 in forum: Shop, Garage and Tools
Post
Harbor freight towable backhoe review.
It looks good all new and shiny but does it dig?
Post by: toolmanmike, Aug 1, 2021 in forum: Shop, Garage and Tools
Post
Harbor freight towable backhoe review.
Did you check the grease in the wheel bearings?
Post by: toolmanmike, Jul 31, 2021 in forum: Shop, Garage and Tools
Post
What kind of pliers do I need for this clamp?
Am I missing out. What happened to the Corbin Clamps? The flat bands were used only on fuel lines right?
Post by: toolmanmike, Jul 23, 2021 in forum: Shop, Garage and Tools
Post
What kind of pliers do I need for this clamp?
Looking for the proper ones. These will crimp the ends closed and push the tab down flat....
Post by: toolmanmike, Jul 23, 2021 in forum: Shop, Garage and Tools

Showing results 1 to 20 of 74 Next >

Search Again

Page 1 of 4

Welcome to our site! Please take a moment and Register today!

Log in / Register

Forums

Photo Garages

Members

Useful Searches

Search Results

Log in

Register