Search results

No there is no rot in that frame rail. Looking at the strut rods fron under the car they appear straight. The photo you have circled is the driver side btw. I may just try adjusting/loosening the eccentric bolts of the upper control arm and see where that gets me.

I am not sure of the history of the car and do not think it has been aligned in a long time. Tire size is 235/70R15. American racing vector rims I believe, backspacing 3.75". I do not think the front end is sitting low. When I did the front brakes I just installed the spindle and discs. I have...

How is caster adjusted? I believe that will move the passenger front tire closer to the rear of the fender. Also, I will try to get photos tommorow. Thanks everyone for the suggestions!

Tire size is 235/70R15. Looking again at the car it looks like the passenger fender is not a 68. On the inside of the passenger fender I see a rectangle not circular hole. This hole is covered by filler on the exterior. Is there a difference in wheel well shape/positioning between 68 and 69?

My 68 has a driver side headrest. The passenger bucket seat has holes in the top of the seat for its headrest so I assumed its missing?

The side with the female spade terminals is rotten. The upper/male side is still solid so either the female or whole connector would be fine. My plan was to find a replacement plastic piece and remove/reinsert each spade terminal one by one into the new one

Hi, I am looking for a 1968 dodge charger passenger front bucket seat headrest. Prefereably gold color.

Hi, I am looking for a headlight harness connector below

Hi, When I turn left, my passenger front tire rubs/bends in the passenger fender lip. It seems the passenger front tire is more forward than the driver front. What could be the cause? I recently put new disc brakes and tires so I am not sure if the issue is with the alignemnt or tire size. What...

Hi, Can someone please post individual pictures of what the belts for the front driver and passenger should look like/where they should connect? I have some belts but I am not sure if they are for the front or back, or even passenger/driver. I also do not see an upper anchor bolt so I presume...

Hi, I need help finding the correct screw/nut size for my 68 charger grill and support. I have attached images below of where I am missing the screws. I need complete screw sizes. Image #1 is by the lower part of the radiator and #2 is the nut for headlight bucket to fender. Thanks!!

Yes but I should have been clearer. I directly attached a 12V battery here to "LOW" and "HIGH" to make the fan spin at two different speeds.

Sounds good, I will try to find it! Well I get 12V at the connector of the fan motor when I unplug the motor. When I plug it in I get ~2V at the connector so the fan doesn`t spin.

Oh ok, so "14T" is connected to 12V or "14BK" when Heat or A/C button is pressed. "14BK" then gets its power from "C1-14BK*"? If so, the instrument panel connector is a single connection connector?

I jumpered 12V to the connector after the heater fan switch and I can run the fan at two different speeds. I also tested the switch and it seems to be working fine. And ok this helps alot, thanks! But where does this "BATT" wire get 12V from? I am trying to trace my way back. I do not have an...

Hi, I am trying to make the blower/ heater fan turn on. I am getting battery voltage all the time at the plug in the engine bay that connects to the motor no matter what position the fan speed switch is in. I assume the fan speed switch sets the resistance in the circuit and when its in the off...

Need rod that goes from tranny to pivot on tranny and pivot on tranny for my 70 coronet 440/727 Also need vertical rod (rod that goes from pivot on tranny to pivot on manifold) for my 69 coronet 383/727. Also need driver side grill bezel and grill filler piece which goes below grill for the 69...

Found the rod that goes from the tranny to the pivot on the transmission, and the pivot itself on th tranny are wrong. Does anybody have these parts? I`m also looking for the vertical kickdown linkage rod for my 69 dodge coronet 383/727 Thanks

Its for a 70 coronet, B body

Column shift