• When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.

Search results for query: *

  1. 6

    72 Satellite Gen III Hemi Restomod

    How about keep the knob and cut the shaft off and reshape cut off end?
  2. 6

    72 Satellite Gen III Hemi Restomod

    FYI, when i installed a tko500 the reverse switch from the a833 screwed into the tko500 and I was able to used the factory harness. Something you might check on if your using the factory reverse light on the dash.
  3. 6

    72 Satellite Gen III Hemi Restomod

    Check the wiring from each pin at the iac to the ecm, you should have a wiring diagram with the holley ecu manual, if not you can download from the holley site.
  4. 6

    72 Satellite Gen III Hemi Restomod

    Yes, Yes and Yes. The iac only has a limited range of adjustment, if the blade is open to far (air leak) then the iac is out of its range of operation. And yes if the pvc, intake, brake booster has a leak then the blade will not close enough. When all of the vacuum leaks are fixed and the...
  5. 6

    72 Satellite Gen III Hemi Restomod

    That is a possibility, because they look the same, might have to check part numbers. When the tps is reset and the iac is at 100% and the idle is at 2000 the blade is open to far for the ecu to control - past idle control. I would start the engine and adjust the blade for the iac to be less than...
  6. 6

    72 Satellite Gen III Hemi Restomod

    Try a TPS reset with Holley setup If the TPS is not reset, the computer might think that you're actually at 10% throttle. Otherwise, you might have to manually adjust butterfly on the throttle body to get the air flow in the range of the iac adjustment and then reset your TPS again afterwards...
  7. 6

    Diagnosing multiple misfires in a computer controlled car

    Check fuel pressure New OEM plugs Test fire injectors Move injectors around to see if misfire follows the injectors
  8. 6

    Rust Bubbles - How Big of an issue?

    I wonder if you could use a bore scope with a light and reach/see from the window opening or the trunk??
  9. 6

    SOLD 1968-70 Wiper Arm Set

    Could I see the spline area?
  10. 6

    Cam shaft.

    I got X and two replies ????
  11. 6

    Cam shaft.

    Daily driver, bracket racer, Street strip what's your end goal for the car?
  12. 6

    1972 Plymouth Satellite Sebring Barn Find

    Nice find! Fellow okie
  13. 6

    What are the steps to properly remove 1969-70 Rear Lower Valance?

    Early junkerup vid's on youtube has pointers on this very topic.
  14. 6

    1974 Charger: puckered and creased jack decal

    one of my old build sheets I put in the oven at 160-180 for a few min to limber it up and then put a weight on it.
  15. 6

    FOUND 68-70 B Body center a/c vent

    I've been on the prowl for the center a/c vent for the charger. I'm looking for someone that will ship and take paypal. Depending on what shows up I'll look for partials/broken and try to 3d print a piece.
  16. 6

    71 Blasted & Primed

    What is the light switch from?
  17. 6

    Vintage Air installation in a 1968 Satellite

    Another avenue it to make your own hardline. I ordered fittings online, some a/c tubing and aluminum soldering kit - flux and rod - and I used a map gas torch. I havn't cleaned them up yet but still holding pressure for 3 years. and yes the port can be used for a pressure sensor or you can...
  18. 6

    71 Blasted & Primed

    That's a nice looking dash! Is that a kit or did you fab it?
Back
Top