Search results for query: *

  1. 493 Mike

    What are the cloth washers in the window track?

    My 65 coronet had leather pads. Mike
  2. 493 Mike

    65 Belvedere fiberglass hood with Max Wedge scoop, where to buy???

    Or you could make a scoop like I did. My hood had the understructure rusted out but the skin was fine. My body guy glued it on after I welded it up. Mike
  3. 493 Mike


    This is the tintable Raptor bedliner I used. Very easy to use and vary the texture if wanted. I detailed a few areas with gloss black and masked them prior to bedliner. I sprayed it over black epoxy. The hard part was scuffing all the epoxy before shooting the Raptor. If top coating the epoxy...
  4. 493 Mike

    63 Savoy front fender repair.

    I can't help but, as a suggestion, look at swap meets for a fender with front rust/damage and splice them. Mike
  5. 493 Mike

    1962, inner fender splash shield question...

    My 65 Belvedere was different. No foam and clip retained, molded rubber seals. Mike
  6. 493 Mike

    1962, inner fender splash shield question...

    I can't address the foam but, install the fenders and adjust them before the splash shields. That will let you set the shields to the contour of the fenders. The shields have large holes to vary placement and fender washers to cover the holes. Place the rubber seals facing the tire, both front...
  7. 493 Mike

    BEFORE AND AFTER - Tri-City Plating, 1966 Charger front bumper

    I had my 65 bumpers done several years ago at North Star (LKQ) in Minnesota and they look equally nice. The back sides are completely chromed, all the rust pits really shine so, I believe they are fully protected. I can't compare pricing with the current financial situation though. Mike
  8. 493 Mike

    Upper fender brace

    What is a ssp? What year car? Can you find a used part? Mike
  9. 493 Mike

    install dodge letters on hood.

    Boy, you Dodge owners have it so easy! We Plymouth owners have 3 more letters to install. Mike
  10. 493 Mike

    Fury Cowl Repair

    The patch panel I purchased did not have the same shape around the wiper pivot so, I removed the OEM area and welded it in the replacement panel. Just a heads up. Mike
  11. 493 Mike

    Monday do over

    It is an attractive contrasting color. Mike
  12. 493 Mike

    Fury Cowl Repair

    Try Kramers or Joe Suchy. Mike
  13. 493 Mike

    Tapping Plates?

    The little 90* tab on the plate hooks on the edge of the hole to keep them in position for cap screw installation. Mike
  14. 493 Mike

    Fender installation.

    I am ready to install the fenders, permanently. I seem to recall some caulking between the fender and inner splash shield. Is this correct? If so , what product is recommended. My FSM says nothing about sealing but, I would think it should be sealed to keep water splash out at the top joint. Any...
  15. 493 Mike

    Custom Sized Fiberglass Hood Scoop

    I fabricated this scoop from an old hood skin. That gave me the OEM ridge. It was quite easy to cut and bend. My body guy glued the scoop to the hood with panel adhesive. Mike
  16. 493 Mike

    I.D This part

    Ford Model A? Mike
  17. 493 Mike

    Installing floor wiring covers?

    I put mine on hinges-welded in after pan installation. Mike
  18. 493 Mike

    Trim clips etc prior to paint

    The more you strip the car down prior to painting the easier it is to sand, clean, mask, and paint. Mike
  19. 493 Mike

    Inner rockers question.

    Epoxy primer. I did the entire bottom with it and then top coated with Raptor bed liner-tinted gray. Mike
  20. 493 Mike

    Polishing Stainless Trim Check this out. I like to support long pieces with a scrap wooden board. They bend like tinfoil when the buffing wheel grabs them! Mike