/ Register

Search Results

Search Again
Page 1 of 2
  1. Jeremiah
    Post

    WANT to DITCH Electronic Ignition 69 A12

    No Pertronix? For some reason I thought the a12 cars came with a single point dist?Edit: A little research and I am wrong they are DP...
    Post by: Jeremiah, Dec 5, 2020 in forum: Electrical & Ignition
  2. Jeremiah
    Post

    1966 Charger - EL dash lights suddenly stopped working.

    Holley efi dash and be done with that junk! Kidding : D
    Post by: Jeremiah, Dec 2, 2020 in forum: Electrical & Ignition
  3. Jeremiah
    Post

    MSD 2-step & Hurst Roll Control - Switches/Wiring for 4-speed car?

    I usually plumb the line lock solenoid to the front brakes so I can release them with the button. My button is mounted fore on the shifter below...
    Post by: Jeremiah, Sep 16, 2020 in forum: Electrical & Ignition
  4. Jeremiah
    Post

    Disconnected TAC & runs awful- what did I do?

    When the car is idling can you see fuel coming out of the boosters, primary or secondary?Have you checked the float level?Does it run a...
    Post by: Jeremiah, Dec 5, 2017 in forum: Electrical & Ignition
  5. Jeremiah
    Post

    Disconnected TAC & runs awful- what did I do?

    Did you disconnect the tach wire from the negative side of the coil?
    Post by: Jeremiah, Nov 26, 2017 in forum: Electrical & Ignition
  6. Jeremiah
    Post

    Installed Msd6a and have run on

    YOu have to tie the little red wire to "start" and "run" as described above. The ballast resistor will be bypassed.
    Post by: Jeremiah, Feb 10, 2017 in forum: Electrical & Ignition
  7. Jeremiah
    Post

    MSD minimum cranking rpm

    Good question on the coil. I have cooked Napa brad coils with a MSD 6AL.It sounds like you have enough cranking voltage that it should have...
    Post by: Jeremiah, Jan 31, 2017 in forum: Electrical & Ignition
  8. Jeremiah
    Post

    MSD minimum cranking rpm

    What is the battery voltage when it's cranking? I don't think the starter is your issue here. Do you have spark at the plugs when it's turning...
    Post by: Jeremiah, Jan 30, 2017 in forum: Electrical & Ignition
  9. Jeremiah
    Post

    ignition control module

    Are you talking about this part:...
    Post by: Jeremiah, Jan 18, 2016 in forum: Electrical & Ignition
  10. Jeremiah
    Post

    Wipers and Clock stopped working 66 Belvedere II

    Disconnect the battery on the car NOW! More often than not the Rube Goldberg-esque wiper switch will fail and melt the entire dash harness back...
    Post by: Jeremiah, Dec 23, 2015 in forum: Electrical & Ignition
  11. Jeremiah
    Post

    Proforma (?) Electronic Ignition Conversion

    I'd install a Pertronix Ignitor ( http://www.pertronix.com/ ) module in your distributor. Much less work for electronic ignition and you don't...
    Post by: Jeremiah, Jul 31, 2015 in forum: Electrical & Ignition
  12. Jeremiah
    Post

    NEVER saw an RB engine distributor like this! What is it??

    The guy you want to ask about this is member "Aero426" on moparts. If anyone would know if would be him.
    Post by: Jeremiah, Sep 1, 2014 in forum: Electrical & Ignition
  13. Jeremiah
    Post

    ignition headache

    I agree that you have a wiring problem. Start with the ignition switch and work forward towards the bulkhead connections. If you don't have a...
    Post by: Jeremiah, Aug 21, 2014 in forum: Electrical & Ignition
  14. Jeremiah
    Post

    HELP!! Replacing Chrysler Electronic Ignition with MSD box and MSD RTR Distributor

    I don't think you can use the MSD ready to run distributor with the MSD box. As far as the ballast resistor goes you can eliminate it with the...
    Post by: Jeremiah, Mar 7, 2013 in forum: Electrical & Ignition
  15. Jeremiah
    Post

    Firecore 50 Spark Plug Wires Review

    They are nice I just wish he would sell the wire in a bulk roll for us DIY guys. Rick are you hearing this brother?
    Post by: Jeremiah, Feb 11, 2013 in forum: Electrical & Ignition
  16. Jeremiah
    Post

    convertible top

    Most of the time Q1, the big red wire, is separate from the dash wiring harness. The end with the spade terminal goes to the breaker in the kick...
    Post by: Jeremiah, Jan 30, 2013 in forum: Electrical & Ignition
  17. Jeremiah
    Post

    66 charger console glove box light

    It is pretty short and comes through the hole in the front of the rear half of the console. It usually falls in the hole and you have to take the...
    Post by: Jeremiah, Dec 30, 2012 in forum: Electrical & Ignition
  18. Jeremiah
    Post

    Re: Hayden 3654 controller

    I tried to use an adjustable single speed controller similar to the 3654 and three of them failed. Hayden would not refund my money. I ended up...
    Post by: Jeremiah, Dec 28, 2012 in forum: Electrical & Ignition
  19. Jeremiah
    Post

    Alternator too big?

    Excellent. Please let us know if you have any trouble and happy cruising!
    Post by: Jeremiah, Oct 13, 2012 in forum: Electrical & Ignition
  20. Jeremiah
    Post

    proper wiring

    You can eliminate the ballast resistor when using an MSD. You will have to tie the "start" and "run" circuit together so you have power to your...
    Post by: Jeremiah, Oct 13, 2012 in forum: Electrical & Ignition
Showing results 1 to 20 of 24 Next >
Search Again
Page 1 of 2
Welcome to our site! Please take a moment and Register today!
  1. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.
    Accept Learn More...