Search results for query: *

I'm looking for a nice solid hood for my 63 Plymouth Savoy, I have a fiberglass hood with 63 scoop on it for trade & $$. I have hinges.

I recently had one of my rockers fail on the dyno, the bronze bushing came out of the rocker on the one side. Does anyone that has upgraded to roller rockers have any laying around that I can buy ? Thanks

I'm looking for a nice front hood that I can replace the fiberglass hood scooped pin on hood that I got with my car. There was a guy out in South Dakota that showed me a couple pics of some in a salvage yard out by him. I would like to know where that was , if he could chime in again I would...

Has anyone heard from Junior in Ky. ? Does he still have the 62 Shawanda Dart ? That was a fast bitch ! I think he goes by Streetking

Just finished the dyno session on saturday before Christmas on the street motor for my 63 and could not be happier. 440 short block, 9.8 comp. KB pistons, 452 heads topped off with Rick Allison's A&A cross ram. Made an EVIL 666 HP and 603 TQ on pump gas from Shell. The kicker is it made 500 ft...

Does anyone have a nice 63 hood & hinges for sale in Ohio, Western Pa. or West Virginia that I can buy and pick up ? Thanks

Does anyone have a nice 63 Plymouth hood & hinges in Ohio or W. Pa. ? Thanks

Who makes a piston for a low deck 400 with a 440 crank and a 4.77 rod ? Is it doable ?

I recently bought a 63 Plymouth Savoy and as I'm standing in front of the car looking at the engine it seems to be crooked favoring the pass side. I know all mopar engines are offset toward the pass side but it looks like the front of the motor is further over than the rear of the engine. Is...

I have a 63 Plymouth with a 440, does anyone have a nice set of 1 7/8 to 2 inch step or 2 inch headders that they are not using ? Thanks

I am looking for a nice set of headders for my 63 Savoy with a 440, either 1-7/8 -2 inch step or 2 inch tubes . I have a real nice set of 2-1/8 adj. race headders that would be better for someone with a much more built up engine. Thanks

Does anyone need a very nicely ported 906 head that was under a max wedge cross ram manifold ? I dropped a valve in the other head and it destroyed it ! If someone else had an issue and needs a real nicely done head I have one, thanks for looking

I know, a very slim chance but I dropped a valve and scratched the cyl. wall. Does anyone have any +.040 pistond for a 440 they would like to sell ? Thanks

Can anyone suggest an air cleaners for the max wedge cars that look similar but not the originals. Mine is not an original max wedge and I want something that looks good but does not have to be correct. Thank you

What is the largest front tire I can run on my 63 Plymouth and not hit the fender lips ? Does a 70 series or a 65 series fit better ? THanks

Engine # OD201098, Trans # PK3410668L 3063 0511, Radiator#2998 968 18398 . This was running a sawmill on an oak skid, I saw it up on a pallet shelf when I bought a 63 Plymouth. Condition unknown at this point but will try to see how it runs and post video of it later. I also have another...

So I found this Big Block motor & trans in a building just south of Cleveland Oh. and I was hoping someone could help me find it's owner. The carb # M3937S, radiator # 2998 968 and below those #'s 18398, engine#OD201098, Trans#PK3410668L 3063 0511. Any help would be greatly appriciated , Thank...

What's the largest (tallest) tire size to run on the 62-65 "B" bodies ? I just got a set of 15X6 steel wheels and I want to buy some tire & hubcaps. Thanks

I recently purchased a 63 Plymouth Savoy that was sitting in a bldg.. for years. I see that it does not have a drivers side mirror ! Does anyone have one for sale ? It's a 2 dr. post car, Thank you

71 Plymouth GTX rear bumper, good chrome, looks good and straight. Asking $400 OBO. The bumper is located in Bedford Ohio, 44146, and can be picked up locally or will meet within reason (about an hour drive), or will ship at buyer's expense.