Search results for query: *

looking to buy 2 15x8 police wheels, 5x4.5, 4.5" bs. Closer to PA the better.

Looking to gauge interest in other members interest in purchasing a weld-in L-bracket to box an Upper Radiator Support. This bracket should stiffen up your radiator support and associated panels. I am going to make one for my 66 Coronet. I have used my 66 and 67 Coronet to do the take-offs...

I have a very nice pair of grill surrounds for a 67 Coronet for sale. IMHO, the surrounds are in very good overall condition for their age. Please be aware both surrounds are missing top of fender mounting straps. These could either be installed as-is (after you obtain all mounting hardware...

Anyone have pics and/or dimensions of the backside of these wheels? Would like to establish - 1. Is the hub face of the wheel and the point where the backside of the wheel meets the rim barrel on the same plane (same point on rim barrel) or does the backside of the wheel meet the rim barrel...

Anyone have pics and/or dimensions of the backside of these wheels? Would like to establish - 1. Is the hub face of the wheel and the point where the backside of the wheel meets the rim barrel on the same plane (same point on rim barrel) or does the backside of the wheel meet the rim barrel...

Has anyone ever taken a close look at the similarities/differences between these rear bumpers? The reason I ask, I'm installing a 68-69 Coronet trunk pan in my 66 Coronet and doing a rear fuel fill. I've seen others that have done similar. I'm looking at alternatives for rear bumper mods ...

Looking for one of the following part numbers - 2120208 - 18-7-2 1/4 2843225 - 18-7-2 2863228 - 18-7-2 2863224 - 18-7-2 2863223 - 18-7-2 1/8

I would like to verify the location of the headrest height adjustment notches on 67 B-body headrests. Are they on the front or rear (facing) side of the rods? From what I can gather, the adjustment notches are located on the rear facing side of the mounting rods. My real question is where the...

I'd love to find a pair of these headrests, wouldn't we all! In lieu of finding a pair to buy; is anyone interested in lending me one so that I could (1) either cast a (non-destructive) mold and/or 3D scan the headrest? I've already deconstructed a few 68-70 headrests and fabricated headrest...

Looking for M-body (or equivalent) power (electric) trunk release. Will be installed into a 66 coronet.

I did a little photo shopping to be able to visual what a 66 Charger rear wheel opening would look like grafted onto a 66 Coronet. I'm planning out the resto of my Coronet 500. Both sides have minor rust at the usual locations ..... lower rear quarter panel, along top of wheel opening, front of...

I am rebuilding factory LCA with sway bar tabs for a street performance 66 Dodge Coronet. I will be stiffening the LCA's with plates and installing a 1 1/8" sway bar, installing heavier torsion bars (either .96 or 1.03), and using urethane bushings most elsewhere. My planning assumption is...

I am rebuilding factory LCA with sway bar tabs for a street performance 66 Dodge Coronet. I will be stiffening the LCA's with plates and installing a 1 1/8" sway bar, installing heavier torsion bars (either .96 or 1.03), and using urethane bushings most elsewhere. My planning assumption is...

Out of curiosity, as well as, to verify components, does anyone know how to decode these stamps (next to speedo)?

Curious to decode and/or understand the block stamping on the driver side of a 400 B, casting 4006530-6. I bought the block for a stoker build and from what I can tell from the pan being a deep rear sump, the dip stick location in the oil pan and the exhaust headers, I believe this engine to be...

I need to replace the trunk floor in a 66 coronet I'm rebuilding. I'm contemplating replacing the trunk floor and gas tank with 68-70 parts. I don't see a need for a 66 spare tire wheel well (for my build) and I like the later 68-70 B body fuel tank profile. From the research I've done, their...