Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature may not be available in some browsers.
When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.
I have a 64 Polara and my question is regarding the plastic portion of the steering wheel. Did Mopar use the same basic plastic steering wheel on the 65 Coronet. I realize the horn rings and center emblems are different.
Found a really nice 65 coronet steering wheel (bare plastic portion only)...
I have a wierd/strange water pump pulley that has an internal spacer spot welded on the inside of the mounting surface. Has original orange paint (unknown origin and don't know what it came off of ? Could be slant 6, 318, 340, 383, 400, 440 ? Measures 2.75 tall and 5.75 O.D.
Is this something...
# 1 - I'm using a cast iron 62-64 water pump housing 2205862. My federal ps pump bolted right up but the pulley does not line up with the 2 groove crank pulley I have installed. Originally the 413 that I'm working on had a 4 groove crank pulley & by doing a quick measurement that pulley would...
Recommendations for fuel pump push rod needed to complete engine build. Plan on using Holley 12-440-11 mechanical fuel pump.
Engine block is 1974
I believe the correct fuel pump push rod length is 3.220
I have removed the vent glass frame assembly from both doors. There are 2 visible screws attaching the glass to the frame.
How do you remove the latch ? I don't see a set screw or any other fastener holding it to the glass.
Help
What thread size of stud do I need for mounting my mechanical fan blade to the water pump flange ? Is there a kit available ?
Using a 2.375 long aluminum fan spacer, steel fan blade is .25 thick & water pump flange .5 thick so I'm assuming around 4" long ?
I see GM kits which are 5/16" coarse...
Just a heads up for those of you looking for the plastic side molding clips for your 64 polara Ed from the Mopar Shop in Madera, CA has them available. $220.00 + a small shipping charge.
They have a website or you can call them. Ed is a very knowledgeable Mopar guy.
Good luck
Any good or bad experiences. Thinking about trying this on portions of side moldings. Car will be a garage queen and will not go though any automated car washes.
Building 64 Polara. Rb 440 big block. 1965 727 slip yoke transmission. Will the original shift cables be long enough with this combination ? Car was a 318 poly with push buttons on the dash.
If i need different cables where can I find them ?
Thanks
PART NUMBER 4120942, DATED 48 2 (BELIEVED TO BE 48TH DAY 1972)
RB BIG BLOCK ENGINES 413, 426, 440 & 426 HEMI
NICE USED CONDITION
COMES WITH NEW CAP & ROTOR
SPINS EASILY AND SHAFT HAS NO WOBBLE AT ALL - SMOOTH
ELECTRONIC (NOT POINTS)
$250.00/ OBO + $15.00 SHIPPING (U.S. ONLY)
PAYMENT BY PAYPAY...
WAS SAVING THESE FOR WIFES CAR BUT AFTER MOCKUP ON FRESHLY PAINTED CAR SHE DECIDED AGAINST THEM. THESE ARE NOS PIECES THAT WERE ACQUIRED YEARS AGO COMPLETE WITH 4 MOUNTING SCREWS STILL IN THE MOPAR PACKAGING.
DODGE POLARA / PLYMOUTH SPORT FURY - 63/64 B BODY MOPAR EXCEPT 880 & WAGONS.
DEALER...
Anybody out there have a diagram or picture of the annodized aluminum filler pieces that go in the center of the rear bumper under the license plate area. These were off the car when I got it. I think there is a difference in models too from 330 to 500 as to how the pieces are shaped and how...