Search results for query: *

Hello So for minor floor pan rust, is there any real rust incapsulating paint or is it all just snake oil ? Been sand blasting anything that I can get too, but there are those spots that it would be awesome to have a magic spray on “ bullet” Thanks

Hello Anyone have any reports on the aftermarket 4spd center consoles for 69 Charger 4 spds and the quality or lack of ? My biggest concern is the very back end that everyone puts their hands and weight on, getting in and out of the back seat, and it gets crushed/cracked like the originals. I...

Hello Refresh my old mind. Did Dodge make a "RT" or were they Coronet Rt's that just had an RT badge on them and no Coronet name plates ? I had thought they did, but it has been a while since I have looked into these. Any history on this subject would be appreciated. I normally am a Charger guy...

Hello I am installing 11.75 rotors on my 66 Charger using the slider type calipers. I could not find any junk yard donors for the brackets so I bought a new manufactured set. Installing my calipers the right side barley rested on the slide, but with future pad wear, it will get better. The...

So my Mechanical fuel pump is leaking This is a 110 gph street strip pump, with a slotted screw on the bottom “bowl” to adjust and point the inlet to where you want it. I can’t remember if it is a Holley or a Carter, but it has the screws around the casting to take it apart and rebuild Picture...

Can anyone give a good reason for me to keep the old drum spindles and the drums them selves, from 66 and 69 chargers ? Swapped over to front disks with the E body spindles,and I can not think there is a need for drum spindles out there ? Maybe keep one set of drums from future replacement of...

Hello What are the Timken inner and outer bearing numbers for the 11.75" rotors used on the drum to disk swap ? A17 the inner/bigger bearing ? Then the smaller/outer bearing is A16? Found a old receipt that had these along with brake pads sooooo ? Thanks in advance

Hello 66 charger had power brakes, putting in manual with discs up front. I have a 69 charger with manual brakes that I upgraded to discs with same componnets. Please see attached picture. I assume the linkage the pencil points too gets tossed into the spare parts bucket, then my new adjustable...

So, I am rebuilding a 66 charger and going to add front disc brakes. I am going to have to move and would like to finish the front disc brakes and block off/ cap the rear brake line after the proportioning valve, and use the fronts only for getting it on and off a trailer and into storage. Is...

Hello 69 Charger Finally bit the bullet and ordered the Legendary foam and vinyl for my front seats. The sent the cloth material you glue onto the foam, but they say I need felt and 1/2" foam for the installation. My bad for not looking into this further. I assumed that the foam kit would have...

FYI Legendary has a 15% off sale going on right now. Ordered my foam and seat covers for my 69 charger. 15% off, Paid for the shipping.

Hello, I have a 2000 Dakota king cab 2 Dr 3.9 v6 automatic 4 wd with 230,000 miles. No 3 and 5 cylinders have ZERO compression. I want to swap out the motor with a salvage yard 3.9 To avoid any potential gremlins, what year motors will drop into this with the least amount of issues ? I want to...

Sooooooooooo, Hang with me here, I'll be getting to my B body question, just follow along. Just did some checking on oil filters for our 08 Aspen 5.7 and 09 Ram 2500 5.7, from the Bosch web site. They call out a 3334. Went to store and 3334 is about the size of a 3600 style that is for a 3.7 v6...

Hello, This is listed on Craig's list. Just curious on what it is. Will it drop in a 1966 thru 1970 b body ? Any info would be appreciated Thanks

Hello, These torsion bars came out of a 68 gtx that was buried in a Iowa corn field slough. They are pretty pitted. I pulled them anyway, they sat in my garage for several years. Are they more than pry bars now ? I have read if your bars had a gouge in them to file it smooth, these might need to...

Hello, Tore apart and cleaned up, and replaced all bushings, ball joints ect in my 66 charger front end. Now to put it all back together, has anyone found a particular order for reinstalling that is easier or better than the FSM ? Just curious, sometimes the workers in the field know better than...

Hello What do you call the notched/ribbed washers that the door springs roll against ? Who sells them ? How do you replace them, the stud they are on is pinned/smashed on the bottom so it looks like you can not just unscrew the studs and swap them out? Any help is appreciated Thanks

Hello I need one door spring for my 69 charger. Please PM me. Thank you

Hello, I bought my 69 charger back in 1988, the guy I bought it from said the front seats were from an early 70s Dodge van. I looked but did not see any part number or markings. They bolted right in, look like they belong, but they need new foam and vinyl covers. I got some pictures with my tape...

Hello, I purchased some rear window interior trim for my 69 charger. The L shaped top sides, and the bottom straight pieces push onto the metal where the vinyl/cloth are pushed on and attached. The bottom corner L pieces have no clips or attachment points. Am I suppossed to glue, double sided...