Search results for query: *

Just curious why there are different driveshaft yoke lengths does it matter, are auto and 4 speed yokes interchangeable. Some are almost 2" longer than others.changer my tranny to a 4 speed with a new drive shaft same yoke that I had with the automatic.

Got two early 1964 automatics to sell cheap I'm tired of bumping into them in my garage. Got cables, three different stall converters, performance torque plate, and a nice console if needed. $250.00 for all parts except console. Console is $400.00

Just ordered a hellwig front sway bar for my 65 satillite. Does anyone know if the kit comes with the tab connectors for the lower control arms or does anyone make weld on tabs? I would think someone could stamp them out don't want to change out control arms just for tabs.

Got an early 70,s a883 4 speed in my 1965 satellite, I've got a new drive shaft being built with a new yoke and u joints. Got some vibration trouble I'm trying to get rid of. Got the tires balanced, checked the axles good there decided to replace the tailshaft housing bushing also bought a Zamco...

Clutch is wet with oil build up I believe may be leaking by the 4 speed trans input shaft retainer seal. New seal in the bearing retainer but doesn't appear to be contacting the machine surface of the input shaft. Doesn't look like the rear main seal on the motor is leaking but, oil is...

489 case 4:10 sure grip posi unit just replace them with 3:55 gears so selling these $450.00 Maine

Got two big block 727 trans 1964 19 spline , custom Frank Lupo stall converter , shifting cables , speed ometer cable , and console for 64/65 b body. May fit others. Reason for sale installed a four speed in my car. Would like to sell as a kit for now. Zipe code 04350. $800.00 Also have the...

Anyone have the pleasure of installing an 11" clutch, flywheel, and Bell housing in a 64,65 b body. The z bar assembly geometry has to be modified. Just checking cause that's what I'm about to do I guess 10 1/2" Is what's surpose to be in one. May have to do a hydraulic set up not sure but I can...

Selling 1963 sport fury convertible as is come and get it. Still some good parts on this car 318 Polly did start in the fall before being covered up. Manual steering box with the column, two bucket seats, lots of trim most of the side trim nice condition.old ford mag wheels, no transmission has...

Would like to put a front sway bar on my 1965 satellite to make it handle better. I need advice on where to purchase a complete set up with the mounting clips for the lower control arms. Car never came with a sway bar.

Going to replace the 4:10 gears with yukon 3:55 and removing the automatic trans for the installation of 4 speed. Doing the gears this winter and collecting parts for the 4 speed change out next winter's project. Money is a factor so got to do it this way or it won't get done. 446 big block 489...

Got a used 11" flywheel for my 4 speed installation. I'm having it cleaned and resurfaced, should it be checked for balance.

Sandblasted a 67 big block bell housing and found a few cracks. Wondering if it us worth weld repair with nirod cast iron weld rod.

Going to install a 4 speed in my 65 satelitte Tired of the leaking automatic. I rebuilt the transmission collecting parts for the 4 speed change over. I understand there may be issues with pilot bearing bore depth. I don't like the idea of cutting the end of the input shaft so I'm wondering if...

Got a new never used was installed but removed it to install 6 qt.hemi pan 440 7 qt. Milidon oil pan and pickup tube 3/8" $125.00 plus shipping ups. No numbers on the pan and no box it's around 10 yrs. Old

Got all the trim for a sport fury convertible for sale. Most is very good to excellent condition except for a couple pieces that have been bent but are still useable. Maine.price is $250.00 plus shipping.

Back again after being non active for about 8 yrs Nice to be active again on this great forum.

Aluminum 4 speed bell housing, clutch fork and bracket for small block. $200.00 plus shipping

1963 plymouth fury grill and headlight bezels in nice condition. $300.00 PLUS shipping

Hello gentlemen I need opinions before cut of my leaf spring perches to relocate the pinion angle. I have had a hard vibration for awhile and I want to get it fixed. I checked the angles of the rotating assembly and found the motor and tranny to be 2 degrees facing down on the tranny tail...