Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature may not be available in some browsers.
When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.
Our Second trip to the Drag strip and I cam home a very happy Camper
The Charger was flying 7.604 @ 90.74
We still have room for a little more improvement
We finally got the Charger to the track last Tuesday
I realized it had been about 30 years since I raced
The car having sat for at least 20 of it
It took me a few passes to get comfortable but the car ran a best of 7.70 @ 90 MPH
There is still more there
I need to play with tire pressure and...
Imagine my surprise when I seen this listyed on Facebook this morning
I have seen it's existence fought over for years but I have never seen a picture of one
Now the question becomes OEM or aftermarket
Link to Facebook add (2nd picture in)...
For those of you that have installed the WO23 hood scoops
Where did you cut the hood?
is it enough to cut the triangular section out of the hood?
or does the hole need to be a little farther back and cut part of the brace?
The Templates I have seen are for a Hemi with dual carbs and the hole...
It's been 20 years since I raced and the old helmet is AWOL which is probably a good thing
This new engine should be fast enough to require a Helmet at the local track
(sub 8's at 1/8th mile track)
So I have been looking for a decent helmet and a decent price
Does anyone have experience with...
I am looking for the light for the inside of the console to fit my 66 Charger
The one that comes on inside when you open the console arm rest
I have the wiring harness and the switch but I am missing the snap in Bezel and lens
pictures for reference (not mine)
Has anyone found a good substitute for the horns in the 66?
I am looking at Sparton horns
They don't have a changeable mounting bracket like the Prestolite horns
There are two style for the Sparton horns
Early Spartons bend away from the body and the later horns bend over the body
Can someone...
I am having a problem with the adapter for my Grant Steering Wheel eating my Turn signal switches. The adapter horn ring wears out where the horn wheel contacts the copper service
in a matter of a few weeks the little wheel will wear through the conductive service of the horn ring and eventual...
I have an annoying problem that I am tired of living with
My Master cylinder leaks out the top underneath the cap
I have tried changing the Masters, I have run the Master as low as half full
I have bent the retention strap until it is so tight I can barely snap it over the cover
I have googled...
I cant say enough about the RetroSound line of radios and speakers
Last night we finished the install of a new Dash bezel, lenses, and RetroSound Radio
I am extremely happy with the outcome
We replaced an original dash bezel that had been cut for a modern radio years ago
We repainted it but the...
I twisted the driveshaft out of my 66 Charger while on the dyno (u-Joint failure)
I am looking at a Driveshaft from PST with 1350 U-joints
My rear end is a 3:91 gear inside a 741 housing
Does anyone know what the spline count is for the pinion yoke?
is it a 10 spline like the 742 rear?
Last weekend we replaced the stock motor mounts on my Charger with set of MagMounts from Mancini
I was worried about breaking the OEM style rubber mount on my 440
While changing the mounts I noticed a spot on my headers where they were rubbing the passenger side inner fenders.
After changing to...
I have had problems with my charger heating up in traffic so I made the decision to an electric fan and shroud. I had no shroud
I ordered one from Champion Cooling who made my radiator. I opted for the high performance upgrade to the better fan
How ever today when we went to install it, The fan...
Well after obsessing for a while I pulled the trigger for new heads and headers
Heads were Edelbrock RPM Heads with 75cc chambers but this is about the exhaust
I went with the Doug's D452s and I have to say they fit like a glove. Plenty of clearance everywhere and yes they fit heads with angled...
I just put new heads and a set of Doug's D452 headers on my 66 Charger
It was an incredible fit with not a single ding or clearance issue
Now I need to cut and run new wires
The Main tube comes up much higher than the old headers and I wonder if the wire looms I am using will keep the wires from...
The recent post on aluminum heads has me a little bit worried
I am fixing to order some 75cc Edelbrock RPM heads for my engine and am glad this came up before I ordered them
Question is 75cc 0r 80cc heads
I had planned the 75cc which would give me 10.5:1 compression (.027 gasket)
is that too...
For those of you that are running electric fans, How did you run the temp sensor?
I am considering a swap to electric fans but I don't want to lose the Temp Dash gauge
This picture shows the factor temp sensor and the plugged hole on the oposite side of the radiator hose
How do I run the wiring...