Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature may not be available in some browsers.
When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.
I am looking for tail light sockets for my 69 Charger. The hole is 1 1/8" and the closest I found in the aftermarket are these:
http://www.oemsurplus911.com/automotive/lightsockets/8544.htm
http://www.oemsurplus911.com/automotive/lightsockets/8545.htm
This is not a restoration so I don't need...
Hi all,
I'm assembling the front of my 69' Charger and noticed an unusual amount of space between the PS of the grill and fender nose. I did not do the body work on this car and the shop that did closed long ago.
The DS gap looks good to me.
I was told both fenders are original but who really...
Hello,
I'm looking for the connector/plug/pigtail that connects to the back
of the headlight switch under the dash for a 68 - 70 Charger.
The car is a 69 but I am using electric headlight doors and building my own
full harness kit so I would prefer not have to buy an entire factory harness...
Due to my triangulated rear suspension my muffler exit area is constrained
in size as the control arms cut into the space before the rear axle.
My muffler exit will be 2.5".
I have tried the tti muffler hangers but they are too wide and will hit my rear control arms.
I like the the thinner...
I am finishing the exhaust on my 69 Charger with a crate 6.4, tti headers and x-pipe.
So far, so good. I also installed a Ford 9 inch rear end with a Control Freaks triangulated rear coil suspension. Also so far, so good.
However, when it came to fitting mufflers, the inner control arms from the...
I'm getting to the point of putting the hood back on my 69 Charger and have to purchase the latch and primary lever mounted on the support (I do have the secondary latch mounted on the hood). Before I purchase and install the factory solution, has anyone found a more modern alternative that...
I'm looking at two different ideas for the seats in my 69 Charger. The Procar/Scat option looks good initially but it sounds like their adapters/brackets for the B-body are essentially useless.
The other option I'm looking at would mounting the factory brackets/sliders and fabbing something to...
My 69 Charger has the multiple holes in the rear package tray (defroster, speaker, etc) but I would like to retain only 2 holes for 6x9's.
I know its a long shot but I was wondering if anyone has seen kits to block off these holes.
May be a good reason to invest in a 3d printer...
Thanks,
-Dave
Has anyone successfully replaced the pedal e-brake with a hand brake
located behind the shifter?
I am installing universal ebrake cables anyway so I was hoping someone
has performed this modification already.
-Dave
I have installed a Vintage air HVAC setup in my 69. Since these aftermarket HVAC systems do not have an 'outside air' option I am trying to decide if I should retain the factory fresh-air box under the driver's side dash. On the other hand, if I replace it with a plate that would make a...
My 69 Charger came with 2 speed wipers. I realize there are numerous posts on converting to 3 speed...but I was wondering if anyone successfully installed a variable wiper setup. Sourced either Mopar or aftermarket....period accuracy is not important to me.
-Dave
My 69 Charger had the trunk and floors replaced. When I went to install the fuel tank I realized there are no holes in the floor for the forward J bolts to hang from. Is this expected with new trunks pans?
If so, does anyone have any location measurements so I can add my own holes?
Thanks,
-Dave