Search results for query: *

This is on a 63 b body , got all the seam sealer off the whole car except in the roof gutters , this isn't coming off like the rest of it did , try heat gun , no go , wire wheel . putty knife ,razor knife , screwdriver takes forever and still can't get it all , it's different seam sealer then...

Was checking out another forum and this person said has engine was running hot , he put new head gaskets on it and he said he drill 2- 5/8 inch holes near exhaust and 3 -1/2 inch holes near lifter valley in his head gaskets and said runs cool , stays at 180 , never heard of this before ? Does...

Looking for 727 valve body 2801856 . Thanks

What is the exhaust pipe clearance between bottom of floor to top of pipe or what is recommended ? Thanks

Did all 1966 dodge coronet have rearends 8 -3/4 741 and 742 ? Going to buy one off this guy he doesn't think its a 8 -3/4 . Google it couldn't find out if they came out with 8 -1/4 or different ones ? Thanks

Who has a 65 Plymouth satellite ,big block ,727 trans. ,742 diff . need the measurement from center of u-joint hole to center of other u-joint hole on driveshaft . Yes ,I look at the sticky on driveshaft length , don't list 65 on down . Thanks

What's the part number for the double lip 742 pinion seal ? Had it wrote down , can't find it . Thanks

Looking for a 1963 b-body sedan 2 door post ,driver side door . Thanks

This is on a 63 b body , would the stock fire wall insulation be better then Kilmat reason asking if I use the kilmat going to weld up holes where the pins fasten the stock insulation on , hate to weld them up . Wonder if I could use seam sealer on holes ? Thanks

Been thinking about swapping a gen 3 hemi in 63 b body and been reading where people are using the A999 AND A518 transmissions behind the gen 3 , question I found a use A999 Trans with numbers 4028465 , 1976-77 model , how much is these going for ? Thanks

Has anybody made there own custom hood hinges for 62/65 b bodies and if so would you show some pictures . Thanks

Have car on rotisserie , turn car clockwise at 2 and 4 o'clock it will stay on it's on, get to 5 o'clock it wants to go to 6 o'clock and beyond in the vertical position by it self . I stop it at 6 o'clock position , Question is it top heavy or bottom heavy ,do I raise it up or down ,it has a...

This is on a 63 Plymouth Bel , here's the question , how does the cable come out of the transmission cross member , want to keep cable . Thanks

Getting ready to pull / six from the top , what is the best pick up points or best place to bolt to motor ,no trans , never did a slant 6 before , this is on a 63 bel . Thanks

Looking for 71-73 reaction shaft 3410899 and front clutch retainer 3515314 , Thanks

Have 63 Plymouth Bev. Trying to figure out a place to mount fuse box , have Autowire highway 22 wiring harness kit . on right side under dash has no room cause of the heater duct work , left side hasn't much room . Anybody that is using aftermarket wiring harness that is not O.E.M where are...

Looking for bouchillon throttle adapter bracket 3352 or a tracing of the outside if it . Thanks

Have brand new set A.M.D front rear inner splash shields for 63 b body . Still in plastic bags and A,M,D box . Take 175 plus shipping . Thanks , Have pics , it said file is to large to process , get pics this week end.

Anybody using the ready to run Firecord distributor FC-1007B ? Found some info on them back 7 -8 years ago about shafts or something like that was bend not running true and again heard but stuff on all brands .Thanks

Will a edelbrock performer rpm fit on a 1963 plymouth bel . with a 440 without cutting hood , Tried seaching for it here but found nothing or I'm doing something wrong . Thanks