Search results for query: *

i installed a disc conversion last summer (MDC62DC) with 11" disc on 1967 Satellite. I'm getting an intermittent grinding noise at left front when applying brakes. Pulled and checked to see something obvious but only see the pad scraping the outer hub when in freewheel. Nothing out of the...

i have 2843675 318 heads(68-71) that i'm about to order intake gaskets. I suspect an intake leak pulling oil. Previously i installed the Fel pro 1213 gaskets. Maybe i'm getting crosseyed and reading too much but i've read all pre-1989 head are 2BBL and as such..would I use the Fel pro 1243...

I can't find a reference in the electrical diagrams to this relay on my 67 Satellite, mounted off inner fender. It looks alot like the stater relay that's at the firewall but has a wire to positive battery side and an inline fuse to the headlight harness?

Found blk w/white wire connector behind dash not connected to anything. Switched power. Also found this bulb. Ash tray light?

I decided I wanted to do the easier ammeter bypass in my 67 Sat by bolting together the feeds and taping up really good. My question is would you expect them to get warm? Secondary question, if I wanted to wire ammeter back up, is there a sequence putting it back on stud, meaning is there an...

past few weeks i upgraded my drums with a Right Stuff disc conversion which included lower ball joint. After disconnecting the steering linkage and reconnecting my steering wheel was off kilter. I realized that something is not right and frontend is more squirrely than previous so I'm going to...

I did a Right stuff drum to disc upgrade a few was ago and all was well. Upgraded to billstein shocks this wknd and was ready to test drive when I lost brakes/pedal to floor. No leaks and it pumped back up. Turns out at almost full lock the back of the single piston calipers hits the shock and...

I'm 2 years post engine engine rebuild and realize after spending alot of time under car chasing what I thought was oil sender, oil pan, oil filter leaks....that its been my rear main seal since rebuild. I believe rubber Fel-Pro was used by machine shop. i'm wondering if he installed upper with...

Installing The right stuff front drum to disc conversion. My question from what i understand is a 10# residual valve is needed to keep the rear drums from pulling shoes back excessively. This kit only comes with an adjustable proportioning valve. My understanding is to mount/install the residual...

so I'm getting around to my front disc conversion (Right Stuff) and at the time of purchase, it was without the MC and proportioning valve and brake rod. I sourced the same MC by all accounts (Cardone 13-1571) w/15/16" bore as well as the adjustable pushrod. I put a call to Right stuff to...

so in a previous thread, my alt was putting out too much voltage. I've since fixed this issue. I'm assuming the high volt. may have messed with my headlight switch. I previously had taken it out to try and "clean" it up due to intermittent issues. I swapped many of the instrument dash bulbs to...

so looks like my voltage reg. is going (15.6v at batt.) and as I verified my alt. amps (60) I thought I read somewhere that 2nd FLD terminal should be grounded. Is that right? As a side note, I purch. the solid state regulator from Ebay. https://www.ebay.com/itm/201249070790

so I swapped my 741 open chunk for a 489 suregrip. Bought a Moog 347 combo u-joint and small side will fit drive shaft but large side doesn't "fit" right in. Wasn't sure if yoke was changed on this chunk but Dia. me asurements seem to be correct. See how the large side(7290) of joint fits. So...

67 Sat. w/ manual drums. Lost half the brakes today. Quick look seemed to be rear brake line leaking. Looking online seems like there's alot of different configurations. I'll crawl under tomorrow but thought it would be easy to order a pre-bent set. Any good online sources?

ride home last night had the low beams flicker and go out. Tried the switch a few times and they came on but went out again. High beams stayed on so I drove home that way. My understanding is the dimmer and switch are one unit? Would that be the most likely culprit or would a instrument volt...

67 satellite and will be swapping rears from a 2.76 open to a 3.23 Suregrip. Have Dr. Diff green bearings kit along with conversion u-joint. As far as I understand, if I had a problem with the 3.23, I could swap the open rear back w/o any other changes, other than my u-joint, due to going from a...

looking to see what guys are running. Post some pics with specs!

Anyone know offhand the backspacing on 14" Keystone wheels? Currently have 225/60-14 rubber, so guessing they are 14x7? Best I could find online is a 4 1/4" BS reference. Just looking if someone knows off the top of their head...I'll measure to verify.

what's the best way to lower the front suspension a couple inches? I'm going to install PST front disc kit and I've already tweaked the torsion bars. Does anyone make 2" lower progressive springs?

I know LED halo ring headlights might not be for everyone but I've decided to go for it. Just wondering what others might have done here. I found this setup....what do you think...