• When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.

Search results for query: *

  1. H

    62-65 Car show

    My 65 on its first trip down the track
  2. H

    station wagon

    Did ma mopar put frames on their station wagons in 1968? I have an interest in a 68 chrysler station wagon and I would like to know what to look for on the rear frame parts etc. cheers Steve
  3. H

    wanted-65 coronet console end

    I need the console piece that attaches to the back of the console and faces the back seat. It is a moulded piece that fastens on and finishes the rear of the console. I believe the 64 consoles are the same. Mine is rotted and badly cracked. Color is unimportant as long as it is good and not...
  4. H

    Thoughts on Snow performance water injection

    Where I live in Northern BC it is increasingly difficult to find good high octane fuel. So I am considering putting a Snow Performance water/methanol injection kit on my 65 Coronet. It is 10.5.1 compression and I sometimes get some detonation. The timing is turned back and the mileage and...
  5. H

    Headliner suggestions

    Legendary I am a dealer for Legendary. There stuff is correct and fits. The headliners are no exception. Just be sure to use a glue that is rated for heat, such as vinyl top glue etc. That way when it heats up in the summmer the glue will not start to come apart. cheers Steve
  6. H

    440 oil pressure

    It was doing it before I noticed that when I had the stock pump on it that the oil pressure was low and that it dropped when I punched it so that was why I put a new pump in. It still had pressure though, 5 psi at idle and a steady 40 at speed. The pickup was set at 1/4 inch from the pan. The...
  7. H

    440 oil pressure

    no tray Yes, I have put 10W30 in it now. I must confess that when I put the pan on, the old pan had a windage tray but I did not use it as I thought it was just part of the old pan system. I know now that I should have used it. Would it make a difference in oil flow if I had?? That is why when...
  8. H

    440 oil pressure

    In my 65 Coronet I have a 68 440HP motor. Bored 40 over, stock crank, iron heads, cammed, eddy performer manifold, headers and 3 inch exhaust. I purchased the motor mount kit from Schumacker as i did not like the way the previous owner had shoehorned the engine into the car. I purchased the...
  9. H

    Lowering compression ratio

    should i try Would it hurt to disconnect the PCV, plug the hole to the intake and then put another breather in the valve cover. So I would have one on each cover. Then run it and check for oil usage and pinging? Do I need to have a PCV valve?? Thanks guys cheers Steve
  10. H

    Lowering compression ratio

    Cam and timing specs Cam Specs: Duration at .50 227 Intake 241 exhaust Gross Lift .486 intake .473 exhaust Timing specs. I sent my torque converter specs 2400 stall 3.25 gears and engine specs with the cam specs and I had a dizzy made for the motor. It is set at: 16...
  11. H

    Lowering compression ratio

    I live in the Northen part of BC Canada. I have to drive my car a long ways to get to any meets, shows or gatherings. My car is a 65 Coronet with a 68 HP 440 Engine. The compression is the stock 10:1. Car should run on 94 plus octane. 91 is around here a little bit, but 94 is hard to find...
  12. H

    Front end wandering need help

    Here she is when I finished her up in June. First burnout All the suspension is new. Idler arms, bushings, pitman etc. Only thing reused was steering box as it seemed okay. I have bought the offset bushings, I think I will put them in and have it re aligned with the positive caster.
  13. H

    Front end wandering need help

    My 65 Coronet Set up as follows 440 RB I think stock small block torsion bars 73 New yorker discs and front brakes( I am assuming that the spindles were used too, as it was this way when I bought it. I just replaced everthing with new parts. I ordered a 65 kit and everything fit, but I found...
  14. H

    1964 Dodge Tribute

    Time for a BC B-body only meet. I am in. How far are all you guys from Smithers?? I would drive my 65 net and meet up. I love that 64, great job. I think I will have to go see the doctor now as it has been over 4 hours!!!
  15. H

    Perplexing brake problem

    This is what I am working on 65 Coronet - stock rear drums (10 inch) - new shoes, cylinders, harware etc. New lines front to back - 73 Newyorker front rotors and calipers 11 inch. - New calipers, flex lines all new brake lines - 68 Newport manual brake master (it looked the same as the...
  16. H

    First ride in Coronet!!

    Drove her for the first time on Monday. Just had to see if she can lay down the rubber. No Problem. I am just tickled. Just have to finish interior now and do some fine tuning. Enjoy Thumbs up!!!! Since I have taken those shots, I have installed hood, grill and rest of front end emblems...
  17. H

    Nuther Canuck 65 update

    Well here she is as of yesterday. Pretty much all of the aluminum is pitted badly so I decided to straighten, sand and paint the grill and bezels until I can afford to buy a better grill. Actually I carried the satin black them to the hood, grill, rocker panel moulding centers, spears etc. and...
  18. H

    Show me your 65 Dodge Coronets

    My Canuck 65 Just fitted hood. Starting to put back together Side shot 1968 HP 440 ready to install Starting shot, before deconstruction
  19. H

    Sure grip advice

    So on the weekend we were running our 68 Moncaco demo car and I am in the pits talking to other drivers and there is a guy who is running this 1970 chrysler something or other, I ask him if he knows of any Sure grip diffs as he has alot of mopars. He says sure and hands me one out of the back of...
  20. H

    Another update on my Canuck 65 Coronet build!

    Motor ready Car ready for motor - Glass in, most trim on, just polishing some more, dash in, new bezels for dash in, front bumper mounted. Just waitin on tranny and then she will go in and hopefully run before the snow flies. nother engine shot nuther shot of car. Very pleased with...
Back
Top