Search results for query: *

I have a 440, stock bore with a cam, dual quads and headers. It also has a Melling HV/HP oil pump and pegs the gauge when the engine is started. The previous owner used Valvoline VR1 10-30 AND added a can of ZDDP. I am considering VR1 in 20-50, Can you have too much oil pressure?

Here is a story of 4 master four M cyls! I purchased my 69 RR in 2019. It had front disc conversion, single piston calipers, adjustable pressure valve for the rear, stock rear brake system, NOT power. (1)The first cyl. leaked around the cap, as it was a rebuilt unit and apparently sand blasted...

I have many vintage Illinois License plates. Yes, in Illinois you are allowed to use vintage plates that are the same year as your car if you have legal vintage plates. Inquire with your required year. These are decent used vintage plates and show bumps and bruises but will clean up nice with...

I have the right and left door belt moldings for an Early A body convertible. These came off of a '63 Valiant. They are in decent restorable condition, one has a bend in it that can be straightened. $50 for the pair. Shipping is an option. Thanks, Ed

Sorry!!!!!

I have the two trim pieces that hold the snaps for a convertible top off of a 63 valiant. Thert is an extra hole drilled in each piece. Normal bumps and bruises for these original pieces. $150 plus shipping.

Here are three NOS 1542 314 Plymouth emblems with the boxes. The first emblem is the best and $100, the second emblem has a dark spot in the lower left corner of the blue and is $85, The third has light scratches in the paint from a staple that was punched through the box. $75. plus shipping

WTB like this one.

I picked up a nail in one of my Hoosier slicks. Took it to the tire repair shop and they patched it from the inside. They said the rubber is so thin on the inside that the cord shows through when u buff it and the patches usually don't hold well. It still leaks!!! What are my options?////////////

I have dual 9605's on my 440. Do I hook up the PCV on the rear carb, rear port , the front carb, front port, or both carbs with a Tee?

I just purchased a car with Hoosier slicks. Is this wear patteren normal and do I need to rotate? side to side?e to side?

I recently purchased a car with a 76 440 truck engine. I just discovered that the valve covers were the early 4 bolt type. Although he said stated "The heads have been milled .030, port matched and had the bowls blended, and had a valve job" he never stated he replaced the heads. Where these...

Hey guys I need opinions on the best way to install this linkage to get the easiest push. In your answer give me the hole number of the pedal, then short arm on the crank,. then the long arm on the crank! THANKS!!!!!!LK

Hello, I have a straight axle on an old Plymouth gasser. It steers very hard. I checked the caster and found that it has a ton of Positive caster. I made temporary shims to tilt the axle and have almost zero caster now and it steers great. Do I want pos or neg caster and what degree of caster...

What would you estimate the HP of this engine? Thanks, LK The engine is a 76 truck 440 with 32,000 miles. I had the block ball honed and cleaned, and new cam bearings. It has new rings and bearings, and a new Melling HV/HP oil pump. New aluminum water pump housing and pump. The heads have been...

I have a new aftermarket stereo (Stereo) I am wanting to install but cannot decide on speakers for my 69RR. I am not looking to rock the neighborhood when I drive down the street, but I do want a clean clear sound when I get on the highway and crank her up. I see speakers priced at $30.00 a pair...

Looking for a mechanic in the St Louis area who is knowledgeable and willing to do a head gasket on a 2002 4.7 Dakota. THANKS

I have 4 Mopar 14 inch trim rings. some dents and curb rash but ok for a driver. $50 plus shipping from 62002

Subject, 1969 Rr with front disc brake conv. and rear stock drums, not power.. with up graded 1 1/8 master cyl. Does anyone make a master cyl rebuild kit for 1 1/8 M cyl???

You might want to check your states VIN tag laws.... https://www.semasan.com/driving-force/quarterly-article/vin-controversy-spurs-action-state-legislatures?utm_content=VinReadMore&utm_campaign=DrivingForce_DF229&utm_id=63785&utm_medium=email&utm_source=iPost