Search results for query: *

Good Day All, Looking to put a lift in my garage. I have 14 foot ceilings. 110 or 220 V power is available. The purpose is mostly to get the car up out of the way for winter to store items underneath....but also to eventually do some work on the car. What's your experience with either and...

Good Day all, I have perfect outside condition 68 charger/barracuda gas cap that is missing the spring loaded plunger piece. Is is possible to remove just the "spring loaded plunger seal" seal section from a poor condition cap and place it on another gas cap that is in great show condition...

Good Day All, I need a replacement turn signal switch for a 69 Charger. Tried to just replace the Cam with a Shemar one, but it still just does not work correctly. So going to replace the entire harness. Which of these three do you all recommend... 1. From Daniel Stern Lighting Daniel...

Good Day All, Looking for the part number for the Oil Pressure Sending Unit for my 68 Charger. Pressure reading unit. I have a parts manual, and usually I am pretty good at finding things in there....but having trouble locating the part number, or a diagram with the part numbered on it...

Good Day all, Does anyone have pics of the correct spare tire bracket that would be for a 69 Charger...the one that sits in the middle of the tire that the hold down rod attaches too? Also...any pics or the factory correct dimensions for the spare tire hold down rod, and how is properly...

Good Day All, 440 Carter Carb 4429S....The original Carb gasket (Part number 2899 145) was it of open design or 4 holed design? Thanks Macdon221

Hi All, Small detail…the white plastic clips circled in the photo….originally were they affixed hanging down like in the photo or were they turned up the opposite way? i am just referring to these 2 clips only and not the rest. Thanks macdon221

Hey All, Got a bit of an issue. 68 440 with 727. I have a metal knocking noise from bellhousing area when stationary, in all gears, but foot on brake. Reading the past posts I decided to remove the bellhousing cover. As you can see…I have a witness mark that of course looks like from the flex...

Hey all, What is the original finish on these brackets on 68-69 Chargers? Thanks macdon221

Good Day all, Moving into rebuilding my front brake assembly. Would like to go back to as close to original as possible. I have local supplier than carries tons of older nos parts so hoping to be able to piece it all together. I have many questions but will try to make them as simple as I...

Hey All, Does the C clips go on the u-joint where it is mounted to the Pinion Flange? Ie where the 2 clamps clamp to the ujoint? if so is the C opening out-facing or in-facing? thanks macdon221

Good Day, Happened to discover the markings on my driveshaft on the tube. The part number 2852162 is self explanatory…as is the DCPC symbol. What is the D8 and what looks to be a “BL” maybe?? Anyone have insight? thanks

Good day, replacing inner axle seals. I did take the measurements before removing. There was about 8mm difference between the sides. Is the difference normal? There were no previous leaks. And no obvious groves in the axle. Should I install the new seals close to the old measurements or...

Struggling to find the Timken Part numbers for the Pinion bearing and race for the front and rear. I have the parts from a vender...but just triple checking before disassembly. Anyone help? Thanks Madon221

Good Day All, I am a learner…would rather try to learn something and get wrong 4 times before getting it right rather than just “get someone to do it”. Besides the FSM that I have…any other good “How to Videos/step by step” or stickys for dismantling and changing the pinion bearings/setting...

Good Day all, I had an issue 2 summers ago with the "chatter" in the rear diff during turns. Pretty loud. Both directions. Ordered the clutch plates and had them replaced. Voila all was fixed and great until recently and it is doing the same thing now....noise when turning both ways. Only...

Good Day, Can anyone decode the numbers on this Carter Fuel Pump? I know the model is 4334 but what about the rest? I did do some searching but didn’t really come up with a definitive answer. Thanks to all! macdon221

Good Day All, Does the top dash(not dash pad), lower doors, upper trim above the doors and small side dash pieces all go the same colour? I know its a “flattened out” texture. It’s for a red 69 charger. Does anyone have the modern day paint codes for that? Tried the paint codes from the...

Good Day All, Been searching for the clips that attach the heater tube hose to the heater box and the dash vents for a 68 b body. Part 1-48-151 "CLIP, Heater Tube Mtg".....number 6026 147. Anyone know where I an find these? Thanks

Good Day All, Trying to source rear quarter lower window trim fasteners for a 69 charger. From various threads/parts manual I have confirmed the parts are... J-Nut 6026 552 Screws 9414 752 Does anyone know where I can purchases these items? Having a hard time finding them. I Think I have...