Search results for query: *

Does anyone know the measured height of the oil baffle inside a 426 Max Wedge valve cover? From the lower lip of the valve cover to the measured height of the baffle. Because of the adjustable rocker arms that were used Chrysler moved the baffle plate higher into the valve cover and this is the...

How do you measure a trunnion driveshaft? I know that you start from the center of the rear u-joint, but then to where in the front do you take your measurement from? Thanking everyone in advance. MadMax3426

Well it happened, I've lost 3 of the 31 needle/roller bearings in the ball and roller to finish assembling the driveshaft on my 1964 Dodge 440 426 street wedge. I do have all of those for the other side. There are 31 in each side of the ball to complete the assembly. I already know that it is a...

I contacted BrewersPerfomance on the question of what to use for the front end of my trunnion driveshaft as far as the right grease to use and they recommended Sta-Lube SL3141 Moly Graph Extreme Pressure Multi-purpose Grease saying that is what they use. So I just wanted to pass on this...

What lube is being used by those who have the early Dodge & Plymouths to lube the front housing and bearings on a ball & trunnion driveshafts? The factory lube 2298247 is what is recommended in the FSM. Today I am replacing the front rubber boot now on my driveshaft and checking out the rear...

I don't know if this has ever happened to anyone else, but I broke off the head of the accelerator screw when I was taking apart the Carter AFB 4 bbl 3611S, from my 1964 Dodge 440 426 Street Wedge to rebuild it. The screw seemed to be frozen in place somehow bonding with the aluminum body of the...

I think that I am right, but it's been awhile and I just want to make sure before ordering these from Classic Industries. Part number #2953 listed for 1970 both B/E bodies. Is there a difference between the years 1966 and 1970s as they only list them for 1970? Will they interchange between the...

I am wondering if any of you have installed this kit as I am having problems with installing the rear cable assembly from the rear wheels to the threaded rod cable mounted in the rear transmission support that comes from the emergency brake pedal assembly in the front under the left side of the...

Well it has got me stumped... When I got my 1964 Dodge 440 426 Street Wedge with the 4 speed it was missing the z bar, return spring and clutch rod set up. I was able to get everything and went to install it today. However when I went to install the clutch fork return spring, I could not figure...

Does anyone know who can repair the heater blower motor from my 1964 Dodge 440? If you have not seen my thread on How to remove the fan from the blower motor, I solved it and posted the new information with pictures for all of us who have these old mopars. It is listed in General Discussions.

Has anyone had this problem before? If so, what's the secret to reinserting them into the plastic connector? I am working on restoring my 1964 Dodge 440 426 Street Wedge. Having a hard time getting the turn signal wiring pins to fit into the plastic connector. Found the way to get the old ones...

Does anyone know how to remove the fan from the heater/blower motor on a 1964 Dodge 440? I do not have A/C.

Does anyone know if I can use the 194 dash light socket as a replacement for the 158 dash light socket. I have a 1964 Dodge 440 and found that a couple of the stock factory 158 dash sockets have broken wings and I can no longer use them.

What rear end carrier was used to house the 3:91 gears in a 1964 Dodge 440 2 door sedan with a 426 Street Wedge and 4 speed transmission? 741 or 742??? I have rebuilt the original engine-10.3:1 c/r and 4 speed and now it is time to move to the rear 8 3/4 axle housing. Axles received new...