• When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.

Search results for query: *

  • Users: 70runner
  • Content: Threads
  • Order by date
  1. 70runner

    Starter voltage test

    OE starter in my 70RR was doing the single <solenoid> click dance a few weeks ago, so I pulled it to disassemble and inspect. Since I had it apart, replaced solenoid, cleaned/checked armature, brushes were good, clutch good, new battery stud and contact assembly (old ones had some divots)...
  2. 70runner

    440 rattle at cold startup

    440-6, 8yr old build, stealth heads, stock manifolds, Lunati 60303 cam/hyd lifter kit, 10.2CR. Brad Penn 15W-40 with Wix 51515. Starts and runs good, except for moderate rattle noise at cold startup. Rattle goes away after 5-7sec. Oil pressure approx 35 at idle, 60 at cruise. Before I yank...
  3. 70runner

    Glass etching?

    Purchased passenger side qtr and door glass for the RR about 6 months ago. Inspection of the pieces prior to install showed no defects, etching, or otherwise. Install was big job, but very careful with the glass. RR has been in the garage since, with a cover. Today I was working on the RR...
  4. 70runner

    Speedo pinion adapter leak

    As shown in pic, leaks between metal housing at end of cable and cable. Everything else seems dry. Is this an inner seal issue?
  5. 70runner

    Quarter glass/frame removal?

    Need to replace quarter glass. 70RR conv though believe it's similar to hardtop. Got the front guide out OK, removed rollers. FSM says to remove regulator arm stud retainers and studs from frame. Can barely see the retainers, let alone remove them. Anyone done this...advice?
  6. 70runner

    Door glass adjustment?

    70RR vert, power windows. Vent frames are correct, from 67B hardtop. Glass is original. Door alignment is good. Passenger door glass is misaligned. When fully raised, it is outboard of roof rail weatherstrip and misaligned with qtr glass at top. If adjusted to bring alignment closer...
  7. 70runner

    57 Dodge D100 project

    Daughter's fiance, retired USMC gunny, just bought this 57 Dodge in Arizona. Has a 318/727 transplant, runs, but needs lotsa attention. The 318 has shorty headers, HEI distributor, 4 barrel Holley and sounds like it might have a stepped up cam. We happened to pick it up on the hottest day of...
  8. 70runner

    WTB 3 speed wiper motor

    Looking for a core that works. Anything between 68 and 72 should be ok. Appearance not impt.
  9. 70runner

    69B Body Strut Rod Interchange?

    Anyone know what years/models will interchange with 69B strut rod? Need one for daughters 69 Charger.
  10. 70runner

    WTB Speedo gear, 39 tooth, green

    For 69 Charger, good used is fine
  11. 70runner

    WTB 68-70B A/C center vents

    Need the 2 A/C center vents for 69 Charger
  12. 70runner

    WTB 69B w/AC heater valve

    Looking for working heater valve (firewall) for 69B A/C car. Also dash center A/C registers.
  13. 70runner

    WTB 69 Alternator

    Core is fine as long as it's rebuildable. Single field, double pulley. Ideally with date code for 19Dec68 build. Edit: single pulley OK
  14. 70runner

    SOLD 70 Sport Satellite

    1970 Plymouth Sport Satellite, yellow with white vinyl roof, white/black interior, 318 V8, 904 auto, bucket seats/console, A/C, PS. Was daughters driver for several years, currently not running. Resto begun, but unable to continue. 99% all there including nice console, dash/gauges, nice...
  15. 70runner

    440-6 rich idle challenge

    .030 over, stealth heads, SRP pistons approx .006 in the hole, stock iron manifolds, Lunati 60303, stock rockers, 10:2CR, TTI 2.5 exhaust, pertronix II with flamethrower II coil. Carbs are new 71 repros, 65jets, 6.5PV, #35 squirter. Engine is on test stand with 727 attached. Engine idles at...
  16. 70runner

    DIY convertible top install?

    Just removed old top from my 70RR conv. Working on frame now. Has anyone installed their own conv top? Would appreciate any suggestions/guidance.
  17. 70runner

    440-6 Build: Opinion?

    70RR convertible: 68 440 block (.030 over) with repro 6pak carbs, 440source alum heads, stock iron intake and exhaust manifolds, stock rockers, SRP flat tops (approx 10:1), SCAT H beam rods, 727, 3.23 suregrip. Mostly street car with a little attitude. Looking at following cam options: comp...
  18. 70runner

    Gas Cap?

    Picture of original "NOT VENTED" Stant gas cap would be mucho appreciated.
Back
Top