Search results for query: *

Hey folks, thought I would pass this on. I am running a FAST efi with a FITECH 6 barrel throttle body, MSD 6al, MSD distributor and coil. The MSD tach wire is connected to the efi module. The dash tictoc tach. needs a signal. The tach. has been reworked for an MSD signal. My question was...

wondering if these HP manifolds will fit 1970 440. Not sure if the parts are interchangeable. Not using them or plan on using them for awhile. Currently using Hedman Headers. (3992-2 is showing for a 68/69 440 magnum L/S, while the 6900 is showing for a 67 440 magnum R/S). The price and...

Gentlemen any info will be greatly appreciated. I’m changing over from a 2 speed wiper to 3 speed. This is on a 70 Road Runner. The motor is installed and wires in. I unplugged the 2 speed switch and plugged the connector on my 3 speed switch and turned them on just to see what would happen...

someone know how to bypass this? It’s on a 70 Road Runner 4 speed

So here's one for you. I rebuilt a 73 440 about 2 years ago. Mild rebuild. I nstalled a Edelbrock double roller timing chain set. With #1 @TDC and #1 valves closed(as they should be) the marks on the cam sprocket and crank sprocket did not line up. I was 180 off on the cam sprocket. Mark on...

So here's one for u. Brand new ignition switch, brand new wiring harnesses throughout car, new starter and starter relay. Car starts 90% of time. Occasionally when you turn the key in the on position and go to start it there is no contact with starter. With ignition on i can jump the starter...

So I picked up some new Reybestos 11" shoes, when matching them up I. noticed the metal was the same but the primary shoe is 1/2 inch shorter and the lining is positioned closer to the bottom of the metal near the adjuster then the one I'm taking off. The secondary is a little longer but...

Before I list on Ebay thought Id run this by u guys. Changing direction and going to a single Carb vs dual quads. These are AFB 600 Comps on a CH28 edlebrock (ceramic coated silver) manifold. Never been on the road. I bought the car with them and they were new. The carbs have been idled over...

So here's one for you Roadrunner experts. My 70 has holes drilled on the tail panel around the lights and following the center groove or contour. It looks like a moulding goes there like on the satellites. C mouldings around the rear light and the full center section connecting each side like...

So guys I know you answer this a thousand times a year, please humor me. My 1970, 440 Roadrunner has a 22" Radiator. I just upgraded to ECP 2 ROW 1" tube Aluminum, FloKooler pump, Miloden full flow 185 stat and new shroud w/stock fan and new fanclutch assembly. The engine has no miles just...

Anybody know how high u can go safely on amps. Currently at 45 W/non AC 70 Roadrunner . Would like to get up to 80 or 90 using the same external regulator, 1 wire alternator. I was told wiring could not handle it ( I don't know what that's all about?)

So here's the rub guys All new wiring harnesses on a 1970 roadrunner my reverse lights stay on all the time I'm wondering if it could be the transmission switch. (4 speed) Before I replace it, thought I would run it by you guys. I have juice at the bulkhead plug both terminals when I turn the...

Has anybody used this tool on a B Body rear fender? Would like to roll mine out of the way, not sure the tool can handle the inner and outer fender lip.

So here's the question. I bought this 70 Roadrunner having never been in one or seen one close up. The dash is a rallye cluster w/tictoch tack. There is an aluminum strip that runs underneath the dash pad assembly and fits in front of the guage cluster (on the top). I think this aluminum trim...

Hope someone can give me some answers. 1970 Roadrunner 4 speed. I'm rebuilding the the steering column, when I got the shaft out I noticed that its 2 Pieces. Like a slip Joint although they don't separate. It appeared to have 4 (2 on each side) plastic plugs to keep it from moving but on...

I have a 1970 Road Runner W/Rallye dash. Has anyone tried to install the RetroSound Model 2 Radio. The dash opening is plenty big, just wondering how the rallye faceplate would line up. No radio or faceplate/bezel in the car now.

Looking for any help ! I'm going from stock 14" wheels on a 1970 Road Runner to 15" wheels. I have an opportunity to pick up 4 15x8. This is a stock body. Has anybody done this? Will they fit? - - - Updated - - - Sorry guys the wheels have a 4" back space, that's where I'm concerned. The...

I have a 1970 Road Runner and would like to go to a 20" wheel on the rear axle, the problem is the speedometer. Has anybody done this, if so did you go to an electric speedometer, what did you use to convert the pulse. This is a 4 speed car. Thanx TroubleMaker