Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature may not be available in some browsers.
When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.
When I bought my Road Runner many years ago, it had a light similar to this one under the hood, not connected to anything. That light is long gone. Now, I have this similar light socket. Is an under-hood light an option in a 70 Road Runner? Where does it get installed on an air grabber hood? How...
I’ve got a ‘70 6-way bucket seat frame that is bent & I need to straighten. It looks like I need to remove 3 of the rivets, straighten 2 pieces and replace the rivets. Where can we buy these? THANKS!
I'm looking for a headlight buzzer diode for a 70 Road Runner rally dash (if that matters). I believe it looks like a "T" electrical plug and two short pieces of wire that dead into each other. Thanks for the Help!
p.s. my wiring looks good and the buzzer works when I leave the key in, but not...
I'm piecing together a new motor & I have a set of Edelbrock aluminum heads with no heat crossover. I street drive this car and want the choke to work (fyi-my factory choke works fine with iron heads). The center six pack carbs don't have the right holes to install a manual choke (what I'd...
I've got a 70 Road Runner and the driver's door latch is old/worn. The star wheel has worn teeth and the pin it rides on is sloppy. The plastic striker is very worn too. I got another on Ebay, but it's not exactly the same. The star wheel and striker look really good on the Ebay latch...
I'm trying to replace my driver's door latch on a 70 Road Runner convertible. I bought a used latch off of Ebay & the listing swears there is more than one design for a 69-70 driver door latch and this one is correct (one on the left). I pulled my latch out (latch on right & 2nd picture) & it...
70 Road Runner 4-speed console car - I bought a matched set of console/glove box/trunk locks. The aftermarket console lock seems like it's a little bit too large of diameter to fit in the hole in the console lid. I'd really like to have a console lock (mine never locked) and only 2 keys...
1970 Road Runner - I'd like to make my tail lights & brake lights brighter. I've been looking at some 1157 LED bulbs and searched the forums here. I saw a reference about "LED turns signals won't work". So my question....is there a LED 1157 tail/stop light bulb that can be installed in a 1970...
I don't know much about electrical stuff. I've added a ton of additional electrical equipment (2 electric fuel pumps, nitrous, bottle heater, purge valve, gauges, line lock, etc). Just about everything is wired "+ of battery to fuse to switch to electrical part to ground" and the wiring looks...
I'm running a set of 452 iron heads on my motor. Years ago, I removed the end exhaust studs on both heads (goes into coolant passages) for header clearance (big tube Hookers, which I no longer have) and used header bolts with RTV on the end stud (now bolt) holes on both heads....worked for...
I've got a couple questions about strengthening a 440 bottom end, stock stroke, to handle a 250+hp shot of nitrous. This is a long-distance cruiser engine (the plan), but I don't want take the nitrous off the car. I've run stock main caps with a 150hp shot of nitrous (current motor), but I put...
I’ve got a 1970 Roadrunner with factory power front disc brakes. I’m having a hard time finding the gasket/diaphragm for the master cylinder cover? Any ideas? THANKS!
I just replaced the original sway bar in my ‘70 Road Runner with an Addco bar. The improvement is very noticeable. The car is much flatter in sharp corners. I would recommend one
1970 Plymouth Road Runner - This car was a street racer, but I'm slowly converting it over to a long distance cruiser. The car has a stock front suspension & super stock leaf springs with 2" lowering blocks (to make car level) in the back. I'm still running the original torsion bars. They...
I'm looking for a 68-70 B-body (maybe other years fit too?) convertible top frame front header....the front "bow" where the top latches bolt on. Does anbody have one? THANKS!
I'm confused. I'm trying to run a 3/8" flexible hose fuel line up to my six pack stock/steel upper fuel lines. Right now I've got a short piece of 3/8" fuel line and the fuel line fitting with the hose clamped on. I'd like to replace that with a 3/8" hose barb.....so where do I get a fitting...
Does anyone know where I can get a valley pan cover that will clear a stock dual plane 440 six pack intake manifold? Am I stuck with a "trim my own" made out of a factory type intake bath tub gasket?
I have iron heads on the engine now & will hopefully be switching to the original open-chamber...