Search results for query: *

Trying to identify this steering gear/box we have on hand. The part number is G-3643311, I can find part number G-3643333 which is close. Any idea where I can search to find out what this box is out of. Thanks

The lens came loose from the taillight on our 76, luckily we didn't lose it. Cannot see what holds it in place besides glue. What would recommendations be for best glue for this project. Thanks

Working on a 440 motor and we need to remove the heater hose spigot. What would be the simplest and quickest way to do this? Thanks

Have a couple of motors here and wondering about suggestions on how best to store for a year or so. Thanks

Want to remove fan on our 1976 Cordoba (360 engine). Got the 4 bolts loose but not sure if the fan is attached to the spacer, it just won't budge. Thanks in advance for any suggestions.

Our '77 Cordoba with 400 motor has been sitting for about 5 years. We fired it up yesterday and the lifters at the front of the motor on both sides are noisy. We changed the oil and that did not make any difference. Thinking of swapping in new lifters but not sure if that will solve the...

Thinking about buying a 400 motor for our '77 Cordoba, found one complete with transmission that has been sitting in storage for approx. 10 years. Will probably try turning it over by hand to see if there is any compression. Anything else I can try? Thanks

Our '75 Charger pulls to the right constantly. Had an alignment done today and it made no difference. Jacked up the right side and that wheel runs free. Any suggestions would be welcome. Thanks

On our 77 Doba with 727 trans it is leaking fluid pretty bad from the speedo cable. It seems to be coming out where the cable pushes into the trans. Not too sure how to get a new seal on there, anybody have any ideas. Thanks

Would like to remove the clock out of our 1975 Charger (same as Cordoba). Does anybody know if this can be done without removing the dash pad? Thanks

Having a problem replacing thermostat on our '77 Doba (400). Can't seem to stop it from leaking. We made sure the surface was cleaned up good, we have a new housing and we are using blue silicone. Wonder if anyone out there might have an idea for us. Thanks

On the 727 in our '77 Doba 400 there is a stripped bolt in the pan and can't seem to stop the leak there. Wondering if anybody has any suggestions what I could get to fill the bolt hole with and then retap it? Thanks

Problem with our '77 Doba with 400 motor when you first start it up and the first time you use the PS it is real hard and does not want to work. After that it seems to be OK. I was going to try to swap the pump but my question is . . . the only pumps we have here are pumps off small block 360...

Wiring up an electric fan and on the relay, not sure if the ground wire should go to 85 or 86. Any help would be appreciated. Thanks

One brand new Passenger Front fender $250.00 OBO and one rust free used 300 Passenger Front fender in real good condition $200.00 OBO. We are located in Ontario, Canada and we would have to discuss shipping if someone is interested. These pics are of the used fender

Going to put an electric fan in our 1975 Charger but kinda confused. They say it runs on a 40 amp fuse and a 20 amp stat so what amp relay do I use?

Are the 75 to 79 late B quarter panels all the same, Cordoba, Magnums, Chargers? Thanks

We are trying to remove the rear seat out of the 1975 Charger. Does anyone here have any suggestions? Thanks

We would like to install this wing on our '75 Charger (hope picture comes out OK) so if anybody has any suggestions or help it would sure be appreciated. The wing does not sit flush on the body of the car. Thanks

Bought a new set of leaf springs for our '75 Charger but we are having trouble tightening them down with the U Bolts, there doesn't seem to be enough room to put the nuts on the U Bolts, what are we doing wrong?