Search results for query: *

I am in the process of door gapping, and after getting the gaps close I thought I should install the upper and lower bumper stops to check the outer alignment to quarter and door position (in and out to the striker) I am working with an original inner door that I skinned with an AMD door skin...

Does anyone have a source for tan headrests? I know PG classics have black, white, blue and red and I could sent mine out to notjustheadrests.com Just looking for options Thank you and Merry Christmas

1970 Dodge Charger front bumper upper and lower reinforcement brackets with filler seal $150 From what I can tell by the 70 FSM, these attach to the upper and lower lip of the bumper and the grill gets bolted to these brackets. US Postal Money order or paypal (freinds and family option, or add...

70 Dodge Charger hood latch support $100 plus shipping The rust that you see is all surface rust. US Postal Money order or paypal (freinds and family option, or add the 4% fee) I can deliver to the INDY swap meet this Saturday (March 4th)

So I used this pic as a starting point to mount my 4 speed brackets so I layed them out and marked them on the floor using tape. (sorry no pics) I had to convert my auto console over to a 4 speed console so I used this template and cut out clearance for the hump So the next thing I did...

1973-1974 Dodge Charger SE 1/4 window exterior louvers $100 plus shipping. US Postal Money order only. Located in Michigan.

1970 RoadRunner GTX Satelite hood latch and support. The latch works freely, it just needs cleaned up. $100 plus shipping. US Postal Money order only. Located in Michigan. It may go on other cars. Be sure of your application.

From what I have found, this is a 68-69 b-body and a-body bench seat headrest. (correct me if I am wrong) It may go on other cars. Be sure of your application. No cracks or splits and the vinyl is soft. $100 plus shipping. US Postal Money order only. Located in Michigan.

1970 NOS Superbird Roadrunner GTX Satellite passenger side quarter panel extension #2963508. Excellent condition, studs are beautiful. Very hard to find. $200 plus shipping. US Postal Money order only. Located in Michigan. (the 2 small spots rubbed off with my fingernail )

I am getting ready to set all the panel gaps and install UScartool subframe connectors. Presently the car is sitting on a body jig. And it will go on a rotisserie to finish out the bottom and all body work. (The body jig supports the car at the 8 frame locations) My question is with the car...

In my case I have spot primed welded areas with duplicolor 2 in 1 primer. Which is a rattle can and is according to there tech sheet lacquer based. Later on I will use K36 urethane primer. I have been told that eventually I would have a problem because urethane does not like lacquer and wont...

Working on my 69 charger panel gaps. I installed an AMD door skin (which has not been welded) I thought I should put the vent wing in and noticed this 1/2 inch gap. There is no other weather stripping installed. Does this look right?

Your help is needed please go to the below link and weigh in https://www.forbbodiesonly.com/moparforum/threads/69-charger-quarter-extension-gap.238322/

I don't think I should have a 1/4 gap under the bottom edge of the extension should I? How do I fix this? Tap the metal out? Add filler metal?

I think my tail panel may be out of position as the bumper bracket holes don't line up. If I could get a dimension along the trunk lock support, from the floor to the high point of the tail panel that would help! I am getting 13-1/4 Thanks and MERRY CHRISTMAS

Another topic brought this up and I would like to know how everyone is fixing these areas. Typically there are 3 areas (on each side of the car) that had the factory lead. Quarter panel 2 roof, a-pillar 2 cowl, and rocker 2 quarter panel. I thought that it was acceptable to weld the entire...

Ok am I missing something? When assemble the roller with the clip on I have a gap between the clip and roller. Comparing to an original roller, the stud is longer by about 1/8 inch. Which is what my gap is. Any suggestions? Thank you

I am getting ready to weld the cowl in and was wondering if my wiper pivots not being in center would be a problem? I guess I could e-longate the hole from the back side

I just talked to my AMD re-seller about replacing the deck filler panel that I have, with a new one from AMD. The panel I have is at least 6 years old and apparently the stamping was off. (Thanks to SGTPaul for pointing this out) It needs to be longer (left to right from the back of the car) by...

I have a question about the installation of my AMD full quarter panels Should the quarters align on the rear window pinch weld? Or should that inner window opening edge of the quarter align with the window edge of the roof structure? The drivers side is good, but the pass side is 3/16 inboard...