Search results for query: *

Quick Fuel 850 Brawler Was on my 440 for a short time while my Pro Systems carb was being built. Choke was removed but all air bleeds and jets are factory. Carburetor was disassembled, and all the old gas was cleaned out, then reassembled with fresh gaskets. It’s been sitting on my shelf for...

Installed and removed. Not enough clearance under my front seat without using spacers under the bench seat. $200 shipped (PayPal friends and family, or you pay fees) to the lower 48. Comes with all installation accessories and 5 ft shift cable. Pay

I got these with a lot of parts I purchased years ago. Valve covers are scratched up and the clearance for the distributor is pretty gnarley. The Moroso breathers are decent but do have some scratches. With that being said, they could be prepped for paint /powder coat and turn out nice. $60 or...

Trying to get the car back together for Turkey Rod run and need a bronze tip, fuel pump pushrod for a 440. I have checked with all available resources and evidently they all are on backorder. Thanks in advance.

I bought this to convert my column to floor shift but changed directions and replaced my entire column. This was never used but does have some small nicks in the finish. My loss your gain as I selling it dirt cheap with the mindset that the market for this item is small/narrow. $75 plus shipping...

Battery is in like new condition. Never installed in a vehicle and still in the original box. Asking $160 obo, shipped.

Mopar M1 Single plane for 440,polished look. Needs to be cleaned up a little. part number p4532174. $150 shipped.

I bought all of these parts off Mike Gaines back in 2015 and my ideas of a new 440 never came to life. 213 casting heads with big valves and port job. Crane springs, locks and retainers with locking valve seals. Heads came off running car but have been sitting, I cleaned one combustion chamber...

Long story short I jumped on the deal to purchase some parts from Mike that seemed like a bargain. The main parts were heads, intake, rocker arms and valve covers. The items I received were not as described and Mike refuses to make the deal right. Here is a link to the for sale ad...

Mopar Performance cast aluminum valve covers. Just pulled from my running 383, could use a little elbow grease to polish them up but are in good condition. They have the baffles installed, filler caps, 1 breather and 1 pcv breather. $75 OBO plus actual shipping. Paypal preferred.

Weiand 8008 dual plane for low deck big block. Could use a little clean up but in great shape, Just removed from my running 383. $100 OBO plus actual shipping. Paypal preferred.

I have a Electronic ignition setup for a low deck big block. Looking to sell for $100 plus shipping. Included are the following parts. 1- Electronic vacuum advance distributor with Taylor cap and rotor 1- Chrome ignition box 1- Accel chrome coil 1- Ballast resistor 1- plug with pigtail for the...

All parts new, Changing directions on my project. Asking $1400 plus shipping. Edelbrock 75cc E-Street 5090 Comp 21-225-4 Comp double roller 2104 Melling oil pump m-63hv Fel-pro head gaskets 1009 Fel-pro intake gaskets 1214 ARP head bolts 145-3606 Mopar M1 single plane 383-400

Driver side is bent up a little and missing one stud, but is fixable. Passenger side is in pretty good shape. Both lens are scratched up. Comes with housing, lens, screws for lens and bezel. $100 shipped.

I found this article and it caught my eye since you don't see a lot of rebuilds using the cast crank. In the article they replace the 6 pack rods with lighter units and swap pistons to a lighter unit that increase compression, nowhere did they mention re balancing the rotating assembly. So big...

Ive owned my Runner since 2001. Its just a little 383 that ive been working on. I have been a member on Mopar Muscle forum for a while and noticed alot of the guys were members here too, So i figured why not?