• When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.

Search results for query: *

  1. 493 Mike

    door panel

    Open the handle and note the screw! The panel is held on with spring clips. Use a putty knife to gently pry the panel away from the door itself. If you feel around with the putty knife you can tell where the clips are located/spaced apart. Try to pry right next to the clips so the door card is...
  2. 493 Mike

    1966 belvedere largest tire

    I mini tubbed my 66 wagon and moved the springs into the frame rails. Easy to do the mini tubs on a wagon! 66 & 67 are quite a bit tighter than earlier or later "B"s. Mike
  3. 493 Mike

    66 belvedere station wagon rear tailgate seal?

    I bought mine from Steele in 2007 for $61.40. Steele part number: 70-2402-85 Mike
  4. 493 Mike

    Is it better to install the trunk lid spring with the hinges up?

    I'll second the dangerous statement! 2009 and still not back to normal. Very close though. Mike
  5. 493 Mike

    Grille support pictures needed

    I hope these will help. Mike
  6. 493 Mike

    2-doorr stainless steel roof rail hardware question

    If they are similar, my 65 Belvedere uses a short round head sheet metal screw with Phillips drive. Probably 3/8" long. My rails were/are sealed to the roof with thin strips of closed cell foam also. Mike
  7. 493 Mike

    Door Panels

    Back in the old days we just bought some vinyl/fabric and made our own. These are a very simple design and you can always spend the big bucks later if you don't like them. Mike
  8. 493 Mike

    ISO aftermarket gas cap that actually fits 66-67? Does it exist?

    I will mail the cap today and let you know the postage cost. Mike
  9. 493 Mike

    ISO aftermarket gas cap that actually fits 66-67? Does it exist?

    I think I kept the cap off my SW. I will look for it. It will be free but, unfortunately shipping isn't. Mike
  10. 493 Mike

    Cowl Gauges

    I have had mine since 1982. Mike
  11. 493 Mike

    1966 Charger Torque Converter 727 /426 Need to source one

    Rebuilding automatics for decades always with rebuilt converters, I never had any issues with rebuilt torque converters. Last one I did came from Rock Auto. Mike
  12. 493 Mike

    66 poly air cleaner

    Don't forget Nick's web site: Nick's Garage - Air Cleaner Identification Mike
  13. 493 Mike

    Door Fuzzy replacement 2 dr hard top

    Are you talking about the halves that staple to the door panels? My set came with staples so, I drilled holes in the weather strips and installed all the staples in their original positions. Not hard, just time consuming. Mike
  14. 493 Mike

    Door Fuzzy replacement 2 dr hard top

    Hire someone to do the job? Mike
  15. 493 Mike

    66 belvedere hand brake install

    I think that assembly is riveted. So, you shouldn't have to. Send me a photo/s so we are on the same page. Mike
  16. 493 Mike

    66 belvedere hand brake install

    I was assuming the 66 was the same as the 65, if so, depress the pedal to access the bumper.
  17. 493 Mike

    66 belvedere hand brake install

    I think you need to remove the rubber bumper to gain the clearance/stroke necessary for cable removal. Be VERY careful to save the bumper. I haven't found any replacement for it. Mike
  18. 493 Mike

    Speedo calibration

    Check with these guys. Mike Speedometer Repair Tachometer Clock and Gauge Restoration for Musclecars and Vintage Automobiles
  19. 493 Mike

    66 Coronet with fresh 512 finally finished

    Great sound! It feels real good to complete a project. I'm seeing light at the end of my own tunnel! Mike
  20. 493 Mike

    Trunk torsion springs

    I worked with NAPA to find the correct capacity struts for my situation. Unless you had identical weight and leverage conditions to me you would need something different. I went thru 3 different models before finding the correct ones. I would start at 100#. Check out my thumb. I swore I was in...
Back
Top