• When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.

Search results for query: *

  1. G

    1972 Plymouth Satellite quarters / side markers

    I bet the pic of the Sherman quarter panels that show the 71 side markers is just a stock photo. Its odd they'd have 71 quarters and sell them as 72 as both were 1 yr pieces with the difference being the markers. I hung full Goodmark quarters on my 71 that came from RockAuto in 2018... When they...
  2. G

    71 airgrabber hood seal

    Mopar B Body 71 72 Roadrunner Satellite Air Grabber Bubble Hump Seal Tape
  3. G

    71 airgrabber hood seal

    I'm not 100% sure what was used at the factory, but my hood was restored back in the 90's. They used what appeared to be double sided 3M tape. It fit perfectly in the groove in the fiberglass around the perimeter and sealed up pretty good. I plan on using the same stuff when I go to reassemble...
  4. G

    Please Help with Front Fender Hardware Locations

    I believe the short ones go into the upper cowl pads that meet up with the fenders square holes(by the windshield). The long ones go into the bottom of the fender where it meets the rocker pannel(2 per side). I think they're so long to accommodate shims if necessary for proper alignment.
  5. G

    Goodmark 71 b body floor

    I used the Goodmark front floorpan on my 71 Plymouth. No issues with the install. I used AMD rear pans & everything went together better than I anticipated.
  6. G

    Your thoughts on phosphoric acid dilution as a metal prep cleaner and tooth structure builder

    I use it 50/50. I brush it on & will leave it for a few days to "etch" into the metal. I use the same Kleen Strip prep & etch from HD that zyzzyx uses. Its got a greenish tint. Sometimes it'll push up some white powder residue that dries & sticks to the surface. It comes right off with...
  7. G

    Your thoughts on phosphoric acid dilution as a metal prep cleaner and tooth structure builder

    I use it. It works great for me on clean blasted steel if they have to sit forany length of time before priming to prevent flash rusting. I always scuff everything before wiping it all down with lacquer thinner before priming. Works for me.
  8. G

    Increasing rear tire clearance in a '70 Charger.

    Hey Kern, your doing a great job! Out of curiosity, what are you running your gas regulator at on your welding tank? I just welded in USCT subframe connectors and had the opposite problem & had to turn my pressure as well as my voltage up to get the weld to "dig" in. I always have to when...
  9. G

    Air Grabber mounting studs

    I need these also & I believe AMK makes them. I've seen them for 70 mustang/cougar on ebay. Not sure they're the same though. Almost bought the kit just to see, as its pretty cheep. On AMK website they have a few different styles/sizes...
  10. G

    71-74 Satellite rocker replacement

    Never used them, but I believe you mean Classic2Current. https://www.c2cfabrication.com/products/1971-74-charger-outer-rocker-panel-2dr-lh
  11. G

    Drip Rail Support

    How big a section do you need?
  12. G

    Drip Rail Support

    No problem. Willcheck in the AM
  13. G

    Drip Rail Support

    I may have a few pieces that you could use for some rotted spots. I got a winshield channel & roof section to repair my upper windshield corners & used some of the windshield drop to scab in my rotted channels on the passenger side. I will check what I have left. These aren't available...
  14. G

    3rd gen trunk panel order

    When I re-did those corners before putting my new quarters on my 71', I didnt touch the rear tail panel or the rear crossmember I left the tail panel extensions attached to the tail panel & was able to remove the welds in the crossmember exts after the trunk exts were cut & drilled out &...
  15. G

    Lower cowl rust repair

    P.S. It WILL take lotsa time to fix rust. Thats why shops are so expensive. Tools are available, & tech is here for you through the rough stuff... Something tells me you may not be ready for the challenge in front of you, though.... I hope you prove me wrong.
  16. G

    Lower cowl rust repair

    You cant "properly" fix that area from just the inside of the car. If you are seriously considering keeping or fixing properly, rust has to be removed, patched, primered & top-coated from both sides...
  17. G

    Lower cowl rust repair

    It sounds as though you are going to need a firewall. Thats where all heater box components are located. The cowl sits on top of the FW & houses the wiper gear. The fresh air vent is in the top of the firewall, under the cowl. If you've got as much rust as it sounds, getting the cowl off should...
  18. G

    Lower cowl rust repair

    What your calling the lower cowl is actually the top of the firewall. You could drill the spotwelds off the upper cowl & remove it if the windshield is out, cleanup everthing, repair/patch any rot & rust, prime/paint, then reassemble. Lots of problems in that area on these cars so many here...
  19. G

    Front frame rail repair.

    There are a few small minor details different between the E-body & B-body. The rail will fit from an Ebody. I put a Goodmark rail in mine & it was listed for both. The differences were a blank hole up front, different shaped flange on the front of the horn corner, and the battery tray hole...
  20. G

    What Happened to the Roof of this '71 Satellite?

    My 71 satty had factory lead with a factory vinyl top.
Back
Top