• When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.

Search results for query: *

  1. Gregg DeGeorge

    1973 318 timing issue

    Yes but thanks ,snow here today,no car time tonight,I’ll hit it tomorrow thanks for your ideas
  2. Gregg DeGeorge

    1973 318 timing issue

    Yes LH front thanks
  3. Gregg DeGeorge

    1973 318 timing issue

    Thanks I will ck it is a new light Harbor freight special ,could be never had a light like this
  4. Gregg DeGeorge

    1973 318 timing issue

    Thanks I marked it with white paint,weird thing when it’s running I can’t retard the timing enough to even get on the marks ,thinking if I move the distribtor gear more to the right maybe that will bring it in now rotor points to 1 LH front
  5. Gregg DeGeorge

    1973 318 timing issue

    Hello everyone working on a 73 318 mild cam fresh rebuild ,after first start up got motor running,broke in cam but can’t set the timing can’t find the Mark when engine is running.Damper is good if I turn it over by hand line up Mark ,number 1 is at top dead center,I have distribtor pointed to 1...
  6. Gregg DeGeorge

    318 oil filter base leaking!!! i can't seal it up!

    I’m having the same problem with a 73 La 318 I’ve tryed twice my engine is in the car trying to prime it with cordless drill problems 1/2 qt on the floor but I do have oil pressure think there’s surpose to be a gasket on that double sided nut that holds flat plate to block the other side the...
  7. Gregg DeGeorge

    Oil filter mount leaking 1973 318

    Happy Hoildays getting ready to fire up a73 318 ;rebuilt by previous owner I was priming the motor today,I have a bad oil leak at filter housing ;I put that together I have a gasket for outside edge the double sided nut that screws into block to hold filter plate The other side the filter screws...
  8. Gregg DeGeorge

    Linkage spring floor shift 1973

    My cars a 73 Barracuda,can’t log on to the e body site ,anyway anyone have a picture of the spring install on the floor shift linkage it’s the fwd where the rod goes down through the floor ,my book is a 70 can’t find a picture thanks
  9. Gregg DeGeorge

    Converter question working on 73 Barracuda

    working on 73 Barracuda tranny already rebuilt its a 318 mild cam ,Parts Geek list a converter but says 727 after it ? Does the 904 use the same converter ?? Its just a cruise night car thanks Gregg
  10. Gregg DeGeorge

    Aluminum rads

    They work great,have used them on two Roadrunners great
  11. Gregg DeGeorge

    Start up help Basics

    Thanks for all the help ,I ordered a new Distribtor seems I’m crushing the rotor cap is moving side to side when cranking weird maybe shaft bent came with used motor I bought thanks again maybe next week
  12. Gregg DeGeorge

    Start up help Basics

    Thanks I have fuel ,new pump is fine ,never ran into this,car just won’t run ,it’s weird I’ll get it to pop off and then nothing ,even pulled top of carb off it’s clean and has fuel I can see it squirt on there thanks
  13. Gregg DeGeorge

    Start up help Basics

    Thanks did not know you can do that I’ll give it a shot before I pull distributor
  14. Gregg DeGeorge

    Start up help Basics

    Thanks have a white spark ;everything is new ,funny it will pop off with starter fluid sounds like timing is off changed cap and rotor points ;distributor is old came with motor ;points seem to opening ;if I pull 1 plug and wire I have spark and fuel just won’t Run ;when I get it to pop off with...
  15. Gregg DeGeorge

    Start up help Basics

    Happy New year first off ,putting together a 69: Roadrunner 4spd 440 car it was an auto switched it over to a 4SPD ;engine is a a used 69 440 steel crank good heads ;my question finding 1 cyl on cap ;myself I normally get engine on compression stroke turn over until it lines up with 0 on the...
  16. Gregg DeGeorge

    69 Roadrunner 4spd conversion

    It is it looked just like an e body 833,has the two shifter locations,Friend of mine thinks van or pickup ,it’s in great shape already over budget,turned down that bearing retainer will give it a try tonight ,thanks for the help thanks hopefully get tranny mounted tonight ,maybe tomorrow...
  17. Gregg DeGeorge

    69 Roadrunner 4spd conversion

    Your probably right thought I did good anyway to tell what I bought ;Brewers for small bearing retainer ?..
  18. Gregg DeGeorge

    69 Roadrunner 4spd conversion

    Can you tell from those numbers if it’s an overdrive hope not ?
  19. Gregg DeGeorge

    69 Roadrunner 4spd conversion

    Thanks no it’s a steel crank 4spd 69 440:I put a new pilot bearing in seems my front bearing retainer is 1/4 bigger than the hole in bell housing ;thinking there’s a larger front retainer on some trannys ;thought tr@nny would work B or e body ;maybe I need a b body only Tranny 69 or earlier not...
  20. Gregg DeGeorge

    69 Roadrunner 4spd conversion

    Hello all ,working on a new project 69 Roadrunner,swapping it over to a 4spd ,thought all was going well but ,I’m using a bellhousing 2892626,bought a used 833 had two mounting places for shifter so I think it’s a 70 or newer ,couldn’t find a date. On it the front bearing carrier is to big in...
Back
Top