Search results for query: *

A fellow member had posted this photo of a '62 Dart wagon pertaining to another topic. When I saw the rectangular steering wheel was surprised as I wasn't aware of this wheel being a stock item on the '62 Darts? Ma Mopar had these unique wheels for a few years; but didn't think they were on...

I have a 727 that’s been in the garage for 27 years and had bought it with a bunch of other parts, including a ‘65 Coronet rear I installed soon after I got it in my ‘63. The guy I bought it from seemed like a walking early mopar encyclopedia saying this trans was a ’65 out of the same car...

Discussion on another thread prompted me to ask ’63-’65 B guys about wheel/tire sizing on their cars. I’m looking to put on 16” wheels with 8” width wheels rear 7” front. I have 15”x7” Magnums 235/R all around on my ’63 now and seems as though still have ample clearance. Has anyone gone to...

Revisiting an old topic I posted about two years ago in case anyone with an old B vert might have any new-news. The re-pop header seal I got for a 100 bucks is part of the weather sealing ills, but not completely. The rubber seal configuration has less meat around the corners above the vent...

Here's a question for Mopar unique projects: With dash resto work, like to refurbish the trans and heater pushbuttons. I've searched the net and have thought of all sorts of ideas; but this is a tricky venture. Before I start trying the ideas collected, have any of you Mopar PB guys restored...

On my '63 Plymouth the left wiper stopped working (right one still works) and it can be swung freely as if a link connection is lost. The factory manual has squat on wiper info. When I look under the dash the left linkage is visible thinking the linkage might be disconnected or broke free the...

Doing some surfing on the net for a new washer fluid bag I haven't come across any for my car. Anyone know where I can locate one of these? Thanks

I have a new rebuilt slightly tricked 318 and motor runs hotter than it used to. To be expected but hear a shroud is advised and maybe 5 blade fan (mine is original 4 blade). Great ideas but does anyone know where I could snag a shroud that would fit my car?

I was going to add to my earlier post about the concerning black slime in my radiator after a costly complete engine rebuild but my alert box has been emptied unbeknown to me; so a new post here. A fellow member said it was stop leak additive. And it is! And thanks to all who replied to that...

I have a question about the kickdown lever I came across while exploring shift point adj for 727 trans on the net. My car originally had a 2bbl carb and I changed over to 4bbl years ago. The shift points were never great but then I know they were set quick on factory specs. I adj the lever to...

Anyone that may have installed new light to fender gaskets on a 63 Fury please let me know how you did it successfully. The gaskets I bought a few years ago at the Mopar Nat's are nowhere near a close fit. They're too short to surround the housing and the location holes don't align. Add that...

I've posted searching for these friggin clips before and thought I finally found them and purchased; but opening the envelope CRAP the wrong clips! I've searched tons of places and no luck. These are to retain the trim along the quarter glass (convert) top body moulding. The body inserts are...

With all of the work reassembling my Plymouth after winter restoration I encountered a problem where the driver's door won't stay tightly shut. Was working fine for a while but had to drill out a broken adjuster bolt on bottom of door, reinstall regulators, windows, etc. Door fully latches but...

Been searching for the fire wall bulkhead block as the one on my Fury has a separated terminal fire hot wire that's loose in the block. Was considering trying to solder this connector so it is secure in the block but not sure how that would work. I haven't found these available so asking if...

After an extensive hunt to say the least I'm asking for some help on some odd molding clips for my 63 Fury. I've posted a photo. The photo shows 3 "H" shaped clips below the rear window that retains a 1-inch wide rectangular trim piece that partly overlays a trim along the top of the body...

I'm installing the window regulators after several months being off the car and to double check myself could a fellow 62-64 B Body owner send me a couple pic's of the felt or "whiskers" as they are on your car? I think a photo of the top of the door and quarter window (convert or two-door)...

Found this item on ebay; can anyone let me know more about this "adapter" part? Thanks

I'm wondering if my cousin's 426/4speed Polara he bought new survived after all the years? He bought the Dodge from Grand Spaulding Dealership in Chicago. The sticker shows VIN 6342I59394. Well if it did survive his kids would like to see photos and any history if possible. Thanks!

I'm going to need all sorts of new rubber and seal parts with the rebuild of my Plymouth after tearing the car down for body work and repainting. This includes: Cowling under the hood Doors inside along the posts (vent window and door frontal area) Windows the window seal strips...

Anyone have any stats on the number of 63 Plymouth Fury convertibles produced? I had the # years ago but no longer recollect. I'd imagine many were crushed as they weren't keeper cars like Mustangs or other "A" list cars. I do many car shows and 4 out of 5 times I'm the only one having a 63...