Search results for query: *

I need a newer scan tool. One that is easy to operate and not to expensive. My older ones are not update-able so I need to do something. So what would be a good one to buy? Must be stand alone, no phone or computer types.

On a 69 Charger does any one have some measurements as to where the bumblebee stripe goes. I have some ideas on parts of it like the center of the stripe at the side marker and the lettering centered on the body line. I just would like some trunk lid lip to stripe in a couple points and maybe...

Does anyone know the dimensions of the hood turn signal recess decals?

Anyone ever get a custom tail stripe? My 69 Charger is not a R/T. Being it has a hemi I was thinking of a custom bumble bee tail stripe that could say HEMI or 528. Just wanting to be different and looking for ideas and a good source to buy from.

Putting my 69 Charger back together. I am most likely overthinking this. I know the caster and camber need to be correct before the toe is set. My question is on the steering shaft. The gear box is master splined and with the spline in the 12 o-clock the notch on the coupler lines up with it...

On 69 B-bodys and others was this left side starter shield used on manual transmissions or was it automatic only?

Are the 69 Charger wheel opening moldings made from Stainless Steel or Andonized Aluminum?

Getting ready to install my hood mounted turn signals on the 69 Charger. They look like they can be mounted either way. The lens is marked front which I find comical. You would think it would say up or down to indicate which way they should be mounted. FSM makes no reference. Any ideas?

On a 69 Charger the secondary hood latch has a couple plastic grommets or bushings along with a round spring washer style retainer. Any one know here one might find them?

On my 69 charger that is going back together. Question is on the spare tire hold down stud/bolt. For some reason I have two in my bag and not sure which one is right. One is about 7 1/2 inches overall with 5 inches of thread and the other is 9 inches overall with 3 inches of thread. I would...

Many years back I bought a used console in pieces for my 69 charger project. I am in the console restoration phase and am doing a mock up to make sure I have everything. Question I have is on the shift plate attachment. On the rear at the console storage compartment there are two holes. Is there...

On a 69 Charger I need to try to plastic weld a couple small areas. Any idea as to what type of plastic this is and what rod I should buy. Not to up on plastic welding.

On the 69 Charger the padded upper door and rear quarter panels have clips. They are made different than the lower door panel clip. Any idea where to buy them? Thanks.

On my 69 Dodge Charger the rear inner catwhiskers/sweeps are stapled to the inner top pad. What is the best way to fasten these?

I am putting my 69 Charger back together and have some minor vent window fitment. First off these are the new aftermarket vent frames. Second I took this apart 16 years ago. I did the left door first and detailed all the hardware. What I noticed was the lower right vent mounting bracket has a...

I am now detailing all my 69 Charger door hardware. I bought new AMD glass and need to install the stainless rear trim that attaches to the glass. I bought the material to attach the trim to the glass. What is the best procedure to attach this before I bumble it up. Thanks.

I am in the process of putting my 69 Charger back together and need some help locating two holes on each side. The headliner was replaced. Prior to replacement I made a template with measurements where the coat hook and shoulder belt elastic strap snap went. Well I can not find it. I have...

I am at a point on my 69 Charger project where the quarter and door glass should be replaced. Years back I bought used tinted glass however they are decent for a driver but not up to my liking for this project. Question is what glass is best? I hear AMD glass has minor size and fitment...

My 69 Charger jack needs refinishing. What is the closest color grey and what color to paint the silver mast. I assume the jack and base are the same color.

On my 69 Charger I am in the process of detailing all the quarter window components. I have a new roller kit on order. Couple of rollers are basic and understandable on rebuilding. However there are two roller mechanisms that have small steel rollers with a plastic roller fixed in a ball stud...