66-70 parts

[moparmarks]

66-9 26" radiator supports 4-piece 275.00ea 66-9 22" 250.00
66-70 front frame rails 350.00ea w/ fender apron 400.00ea
T-bar x-members 250.00ea
flat hoods. 68/9 Sat. 100.00ea
floor pan supports 75.00 set of 4
rear foot well floor pans 68-70 150.00pr
under rear seat pans 300.00
cowl/firewall w/jams 66-70. a/c or not 400.00ea
trunk hinges 80.00pr
trunk hinge rods 45.00pr
hood hinge cores. rust free. 66/70 45.00pr
68-70 A/C heater boxes 85.00ea
68-9 auto shifter steering columns. P/S 50.00ea
68/9 70 dash frames non-Rallye 50.00ea
V-8 K-frames 1966/9 75.00ea, 1970 100.00ea
66 Coronet lt HT door. 200.00
67 Coronet quarter panels sedan 750-900ea
68 Coronet d-lid some dents, some rust in front corners, nice pocket 400.00 sold
68 Coronet lt fender 325.00
69 Coronet deck lid SOLD
69 Coronet lt fender 200.00
68/9 Coronet ft bumper Good driver 100.00
Bumper Mts 45.00pr 66 68/9 70 Coronet
66 Sat/Belv lt fender very nice 450.00 SOLD
68 Sat rt fender 275.00
68 Sat lt fender 325.00
69 RR lt fender very nice 450.00 sold
69 RR lt fender 250.00
70 Sat rt fender 275.00
70 Sat lt fender 300.00

As always, free delivery to the following shows with prepaid or deposit:
Spring and Fall Flings, MATS, Carlisle, NATS and Indy. Also long I-70 I-15 between home and the shows.

 

[Tim69R/T]

What do u mean about the 26 inch rad, supports four piece? And any pics?

 

[detmatt1]

I think he means the top yoke, both sides and the bottom which are sometimes easier to remove seperately.

 

[moparmarks]

:headbang:

 

[74 RR 340]

do you have any rear window lower corners for a 68-70 b body ?

 

[1badgtx]

Lookin for a 66 to 70 console top...Auto with no factory tach mount..
Petty Blue 67 gtx

 

[moparmarks]

do you have any rear window lower corners for a 68-70 b body ?

Sorry I don't right now.

 

[moparmarks]

Lookin for a 66 to 70 console top...Auto with no factory tach mount..
Petty Blue 67 gtx

Sorry don't have

 

[moparmarks]

What do u mean about the 26 inch rad, supports four piece? And any pics?

The lower, upper and both sides still togther. Heres a pic before I drillled it out. Guess I don't have an after shot. I sold this one but just got a 66 in with a 26" that I still need to remove

 

[66coronet500]

Looking for a pass side mount that goes under the sill plates. The sill plates screw into them. For a 66 coronet 2 door hrdt.

 

[moparmarks]

Have a couple 66's and neither have a plate under the sill plates. ??

 

[kb67mopar]

Looking for a pass side mount that goes under the sill plates. The sill plates screw into them. For a 66 coronet 2 door hrdt.

Have a couple 66's and neither have a plate under the sill plates. ??

I have a 66 4-door that has the piece you are talking about, its a small piece of galvanized steel that the sill plate screws to. Unfortunately they would be too short for your 2 door (I could sell you all 4 and you could make it work)

 

[shorty64]

Wire Runs???

I think they are called "wire runs" or something similar. Purpose being to channel wires from front to back, etc I imagine. I found a pair on e-bay years ago just by luck for our '67 Charger. I can take a pic and send it if it helps everyone out.

Randy C.
Newaygo, MI

 

[moparmarks]

I think they are called "wire runs" or something similar. Purpose being to channel wires from front to back, etc I imagine. I found a pair on e-bay years ago just by luck for our '67 Charger. I can take a pic and send it if it helps everyone out.

Randy C.
Newaygo, MI

Those would be the wire races which I do have.

 

[66coronet500]

Have a couple 66's and neither have a plate under the sill plates. ??

Here are some pics. Need pass side. It is the maroon part in pics. Not the wire runs that go under the carpet. These are under the sill plates.

 

[moparmarks]

Thanks for the pics. Will have another looksee.

 

[kb67mopar]

Here are some pics. Need pass side. It is the maroon part in pics. Not the wire runs that go under the carpet. These are under the sill plates.

Measure yours and tell me how long they are, I can measure the ones on my 4 door and let you know if its the same...I am parting it out anyway.

 

[66coronet500]

Measure yours and tell me how long they are, I can measure the ones on my 4 door and let you know if its the same...I am parting it out anyway.

37.5 inches long

 

[moparmarks]

I do have one from a 66 Coronet 2-dr sedan. Real nice pass side.
PM me your e-mail and zip code for pics and a quote.
Beings how this matches the sill plate a 4-dr will be shorter.

 

[kb67mopar]

Since he has one I won't bother seeing as how this is his for sale thread anyway.

(sorry for hi-jacking, only meant to help)