Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature may not be available in some browsers.
When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.
What I think you will need to do is look at Dorman products. They make aftermarket parts and here in the US they have all sorts of plastic clips for moldings. My guess is that you will have to measure your holes in the A pillar and try and find a clip that you can file down to fit the trim...
What radiator are you using a small block or big block rad? The small block rad has the hose in the middle of the top tan, the big block has the upper hose on the passenger side of the rad (top) It is kind of hard to see if there is an indentation (slight curve of a cutout on the top half of...
http://www.superformanceproducts.com/catalog/2016SuperformanceCatalog_RacerNet.pdf
Not sure on your port size but there are a few options here and the gaskets are quality in my opinion. If you are going to use any sealer on the gasket, use a non-hardening permatex on the valley pan side. Im...
I'd say that the intake to cylinder head angle is off and therefore oil is starting to get sucked past the gaskets. There is a way to check to see doing a dry fit of the intake minus gaskets and seeing how much clearance you have. I dont remember the exact procedure but its not hard. Hughes...
Special T is NOT cheap. I brought him a few pieces that were already stripped, straightened and polished out all they needed was to be bright dipped. I paid for it big time, meaning that I paid for straightening and polishing on top of the bright dip. Bill is a nice guy, but the next time I...
I'd definitely would crawl under the car and look at the transmission and see if whomever swapped from the 361 to the 318 left the oem cables in place. Ive heard of guys putting an aftermarket shifter in the console so they have the oem interior look. Hopefully this is the case for you it will...
What kind of shifter do you currently have in the car? Is it the column shift with the selector cable and park cable? Or did the previous owner put in an aftermarket floor shifter? If that is the case, then the transmission year is kind of moot point, other than possibly the rear mount. You...
I have a B block cast iron dual point distributor #24444360. The shaft spins freely and there is no wobble. Missing the vacuum advance canister. I can bring to the Indy swap meet in March.
$75.00
I have a RB Steel crank that is STD on both rods and mains. I just had it magged this past weekend and it passed. Machinist says that it will polish up at std no problem. There are a couple of little pits on a couple of the journals that he said would clean up at .010
I can bring to the swap...
I am planning on going to the Indy Trade show on March 4th. I have a set of MW exhaust manifolds that I no longer need. They have been repaired professionally years ago, they have been sitting on a shelf collecting dust ever since, time for a new home. $650.00
Bring a flashlight and crawl up under the dash and look up towards the wiper pivots. The seals that go around pivot shafts dry out and leak water down to the carpet, which then leads to rotted out floors due to damp carpet. Passenger side pivot will be a challenge to see because of the heater...
I might have one for you. I will have to mic to see what the journal sizes are. I bought it years ago as a spare, I have no idea on the history. Its in good shape no scoring on journals.
Ok on the sail panel there are 2 plastic clips on either end of the trim piece. Now they look to be the same size as the side body moulding clips. They ARE NOT!!! they are small in width and are not reproduced that I am aware of. I bought a few repops years ago from Joe Suchy and last I heard...
A low grade rubbing alcohol 70% in a spray bottle to cut the grease and muck. It will evaporate fast especially if you use an airhose to assist drying.