• When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.

Recent content by 07charger67

  1. 0

    Personal Favourite '74-79 Mopars

    These cars I could see being the next classic mopars now that the older ones are so outrageous in price. Not everybody can afford a 69 or 68 or whatever R/T or Hemi or 6bbl. I know how you guys feel, I have a 67 charger and some people don't even now its a b-body or dodge ha-ha. There are...
  2. 0

    Mopar engineering that ticks you off!

    How about badass cars that you don't see any where except mopar nats ha-ha thats my favorite thing. Most people that see a 67 charger probably think its a toyota concept car ha-ha-ha. My least favorite engineering thing is probably that its hard to find parts sometimes.
  3. 0

    8 3/4" rear end

    Can you set the gears in the center section outside the car? Can I just take it out and give it to a shop then put it back in when they set them?
  4. 0

    Before you Vote - Alarming information about the Communist Party

    The difference between the people in the white house now and the people in russia and china is that we can still vote them out and change stuff. I don't know about fascism and communism, but if it were truly what the USA was right now you would all be dragged out in the street and shot for...
  5. 0

    Water Temp Sensor Location???

    Just to let you know, that an aftermarket electric temp sender will fit in the stock sender location if you don't want to use a mechanical one.
  6. 0

    Warning

    You don't even have to think about 9/11, think about ww2 and all the people lost in that. Talk about people with big berries!!!
  7. 0

    Another Strange Dash Light issue...

    Not to hijack this thread but do any of you think that the ground wire for the headlights on our cars are kind of small?
  8. 0

    New 383 runs really bad/Please Help

    Well I have, and I blew up a muffler doing it too, it ran like it had no compression thats why I said 3 to 1, I didn't really check it. It ran awful, some times it would run and then sometimes it would back fire out the carb and the intake would get really really hot. Trust me an engine can...
  9. 0

    New 383 runs really bad/Please Help

    An engine can run 180 off ignition timing because mine did that until I fixed it "it ran with no power and stumbled". Think of it this way, the piston is going up and the exhaust valve is open, when the piston is almost at TDC the spark plug goes off and ignites whatever fuel/air that is left...
  10. 0

    End play on axle

    I felt the rear u-joints when I was under there with both hands and it didn't move at all "slop". I didn't do the front ones though.
  11. 0

    End play on axle

    All I know is that after I put it up on ramps it makes this squeaking noise. I'm going to borrow a dial gauge and set it again tonight. The u-joints are non-greasable ones.
  12. 0

    End play on axle

    Well you can't hear anything when I put the wheels back on. I did drive it last night for a couple of miles and took a bunch of turns to see if I could hear any noises which I did but I think its coming from the front end. I did have a lot of end play so I had to adjust it! After I drove the...
  13. 0

    Help! Over charging again!!

    Yeah your battery could have a short in it from running such high voltage, that happened on my truck once. It was charging at 17 volts!!!!!!!!!
  14. 0

    Plastigauge accuracy?

    I would assume so, engine builders use it. I think they put the bearings in then put the right torque on the cap bolts then take it apart and see how much it smashed and thats the tolerance. I think packages even come with a measuring device.
  15. 0

    End play on axle

    Ok so I read the manual and tried to adjust the end play myself. It took a couple of mallet hits and adjusting of the axle nut but now I have no end play that I can FEEL. Now the manual shows a gauge that will tell you the tolerance! I can spin the axle and both sides will not move in and...
Back
Top