• When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.

Recent content by AJReigart

  1. AJReigart

    Short answer is no I have not found a 'good/economical' way to reproduce these headrests...

    Short answer is no I have not found a 'good/economical' way to reproduce these headrests economically.
  2. AJReigart

    WTB WTB - Two (2) Cop Wheels - 15x8, 5x4.5, 4.5" bs

    Yes, my understanding is that most 15" Cop wheels are 15x7, 5x4.5", 4.5"BS. However, I believe that some late 60's/early 70's Plymouth Fury cruisers had 15x8 wheels.
  3. AJReigart

    WTB WTB - Two (2) Cop Wheels - 15x8, 5x4.5, 4.5" bs

    looking to buy 2 15x8 police wheels, 5x4.5, 4.5" bs. Closer to PA the better.
  4. AJReigart

    FOR SALE 66-68 Upper Radiator Support - L-bracket to box the crossmember

    Thank-you for the advice. I took the upper rail out of my parts car this morning. Will clean it up, get some 3/4 square tube and roll the upper edge. Will use it to prototype an L-bracket to box the rail.
  5. AJReigart

    FOR SALE 66-68 Upper Radiator Support - L-bracket to box the crossmember

    All good, discussion and feedback .... also good to know that factory and repros (AMD, I assume?) are so close (aka identical) .... surprise, surprise. I have the upper rail of the radiator support out of my 67 Coronet parts car ... gonna use it to prototype and test fit the initial L bracket...
  6. AJReigart

    FOR SALE 66-68 Upper Radiator Support - L-bracket to box the crossmember

    Curious, is that pic of a factory upper radiator support of a reproduction? I just measured the upper rail flange at your arrows on both sides of my factory 66 and 67 radiator supports; as well as, several places across the "flat" top. The measurements vary by .1"; .8" in the radius between...
  7. AJReigart

    FOR SALE 66-68 Upper Radiator Support - L-bracket to box the crossmember

    I have! Look at the pic, this piece installs under the radiator support corner braces.
  8. AJReigart

    FOR SALE 66-68 Upper Radiator Support - L-bracket to box the crossmember

    I appreciate the input. I lifted this concept from an FBBO restomod build, with his permission. The "L" shape piece is designed to retain stock radiator support dims/overall shape to the extent possible. As you know, the stock radiator support upper rail flange width is held at 1" across the...
  9. AJReigart

    FOR SALE 66-68 Upper Radiator Support - L-bracket to box the crossmember

    There is nothing wrong with my existing radiator support. Probably nothing wrong with most of them. However, I have my car torn down to the unibody. I've identified all the body areas to be repaired (due to rust, the car was never in an accident). I've obtained the necessary repair parts...
  10. AJReigart

    FOR SALE 66-68 Upper Radiator Support - L-bracket to box the crossmember

    No offense taken ..... cost is what it is as I'm having them made by a shop. I didn't put this offering out to make a profit, just offering to do so for the FBBO membership .....
  11. AJReigart

    FOR SALE 66-68 Upper Radiator Support - L-bracket to box the crossmember

    Looking to gauge interest in other members interest in purchasing a weld-in L-bracket to box an Upper Radiator Support. This bracket should stiffen up your radiator support and associated panels. I am going to make one for my 66 Coronet. I have used my 66 and 67 Coronet to do the take-offs...
  12. AJReigart

    SOLD 1967 Coronet Grill Surrounds

    I have a very nice pair of grill surrounds for a 67 Coronet for sale. IMHO, the surrounds are in very good overall condition for their age. Please be aware both surrounds are missing top of fender mounting straps. These could either be installed as-is (after you obtain all mounting hardware...
  13. AJReigart

    YearOne cast aluminum Mopar Rallye wheel - Part Numbers: MRW179SLVS (5" backspace) and MRW178SLV (4.5" backspace)

    Rough sketch of Inside Wheel Profile - 17" diameter rim provides up to 14.5" diameter x either 4.5" or 5" backspace. Assumes caliper/rotor stay within red line (perimeter)
  14. AJReigart

    YearOne cast aluminum Mopar Rallye wheel - Part Numbers: MRW179SLVS (5" backspace) and MRW178SLV (4.5" backspace)

    Assuming you lay a straight edge (yardstick) across the back of rim - 1. Is the measurement 4.5 or 5" from hub face to bottom of straightedge? 2. What are the measurements from the bottom red line to first, second and third red lines? a. first line being the start of wheel bead lip...
Back
Top