• When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.

Recent content by Indetrucks

  1. Indetrucks

    FOR SALE 66/67 B body strut rods.

    Do we know if these will work on a 70-74 Ebody?
  2. Indetrucks

    Can anyone ID this K-Member with LCA's?

    I'll ask, honestly didn't know there were date codes stamped there. Is the stamp on the bottom or the top of the front end of K-member?
  3. Indetrucks

    Can anyone ID this K-Member with LCA's?

    What about the LCA's, are they the same as my 70 Ebody?
  4. Indetrucks

    Can anyone ID this K-Member with LCA's?

    I have a 70 Cuda w/ 340 small block and was hoping this K-Member with LCA's would work. Seller isn't sure, but thinks it will. From the awkward pics and my inexperienced eye, it looks ok? If it will work, do you see anything of concern or why I shouldn't use it? Thank you for your help!
  5. Indetrucks

    SOLD 1968-70 Strut Rod Set

    Msg sent
  6. Indetrucks

    WTB Wanted: Carter 4933 Carburetor (Rebuildable or Working)

    Wanted: Carter 4933 Carburetor (Rebuildable or Working) Would love to put the original Carter 4barrel back on my 4speed. Shipping to 90717 Thank you!
  7. Indetrucks

    Shaft seal leaking on my 68 Charger 383 P/S pump, replacement or seal kit? (pic)

    From ALL the info I have been reading, you will need a press. I watched a few rebuild videos and while I can rent a free puller from my local auto store, the rebuild of my TRW pump is a little overwhelming. Been reading of people having issues after they tried the rebuild themselves and am...
  8. Indetrucks

    Shaft seal leaking on my 68 Charger 383 P/S pump, replacement or seal kit? (pic)

    Looking at the back of the pump, it looks like the Large Notch TRW pump on the left and the front shaft has no hole/hex. It sounds like I need the Edelmann kit part number 7897 . Thanks so much everyone! Now I need to figure out if I need a special puller or tools for he rebuild.
  9. Indetrucks

    Shaft seal leaking on my 68 Charger 383 P/S pump, replacement or seal kit? (pic)

    Nice, I have no idea which kit to buy, which was the intent of this thread. Did you need a special pulley in order to rebuild it?
  10. Indetrucks

    Shaft seal leaking on my 68 Charger 383 P/S pump, replacement or seal kit? (pic)

    I have no clue which pump I have. Can anyone help ID this and point me in the right direction for either a replacement or rebuild kit? I'm also open to having it rebuilt professionally. Thanks!
  11. Indetrucks

    68 Charger Disc / Drum conversion done - A couple problems/questions regarding distribution/proportioning

    I do not and I just had surgery, so it will be hard to provide in the near term. But it's very basic, both lines out of the dual master going in to the dist. block. From the block, front two lines to l/r front calipers and rear line from the dist. block goes to prop. valve and then to the rear...
  12. Indetrucks

    68 Charger Disc / Drum conversion done - A couple problems/questions regarding distribution/proportioning

    Ye, they are both installed. Should I remove the distribution block and just run the rear prop valve?
  13. Indetrucks

    68 Charger Disc / Drum conversion done - A couple problems/questions regarding distribution/proportioning

    No fluid loss. Perhaps I need to delete the distribution block and put a metering valve in its place?
  14. Indetrucks

    68 Charger Disc / Drum conversion done - A couple problems/questions regarding distribution/proportioning

    Prop valve in, brake pedal still soft and going to the floor. Bled the master, no bubbles and bled the brakes multiple times, no air. The car DOES stop and will lock up the brakes, but the pedal is literally on the floor. Do I need to delete the Distribution Block that the previous owner...
Back
Top