• When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.

malex's latest activity

  • malex
    malex reacted to fullmetaljacket's post in the thread Rebuilding LemonWedge. with
    Like
    Like
    .
    LW. You can fab and run beads well. Go for it. I agree with Maestro DVW. I did my own 12 point roll bar with the car on eight horses on...
  • malex
    malex reacted to Tex013's post in the thread Rebuilding LemonWedge. with
    Like
    Like
    .
    Where do your safety rules fall exactly re rollbar , cage , safety clothing etc ? Here in Oz when I first got to that thinking ...
  • malex
    malex reacted to fullmetaljacket's post in the thread Rebuilding LemonWedge. with
    Like
    Like
    .
    Same here just as DVW. Scratched built the trans tunnel out of found metal out of a metal shop in the Navy Yard. bent it over some...
  • malex
    malex reacted to dvw's post in the thread Rebuilding LemonWedge. with
    Like
    Like
    .
    The trans tunnel. Cut th.e hole leaving the throttle pedal mount and the stock tunnel are from the torsion bar cross member rearward...
  • malex
    malex replied to the thread Rebuilding LemonWedge..
    I sure can relate to Tex’s point of view on setting a goal and building back from that. I think we all start out that way. I did. In...
  • malex
    malex reacted to 6PKRTSE's post in the thread Rebuilding LemonWedge. with
    Like
    Like
    .
    I didn't move anything back 3/8" or have to machine the water pump houing 3/8" to use the front plate. All my accessories mount to the...
  • malex
    malex reacted to dvw's post in the thread Rebuilding LemonWedge. with
    Like
    Like
    .
    I ran gaskets on the plate on my previous car. After a while they would leak. This car has used Ultra Grey with no gaskets for 13 years...
  • malex
    malex reacted to GTX JOHN's post in the thread I didn’t know we had a famous member with
    Like
    Like
    .
    I was on the covers of both Hot Rod and Car Craft the very next month. Also, the full back page of Hot Rod and the center two pages of...
  • malex
    malex replied to the thread Rebuilding LemonWedge..
    A 3/8” front motor plate and a couple of limiters and you’re good to go. This will get you close for plate location. The AR plate...
    • IMG_6499.png
    • IMG_6500.png
  • malex
    malex reacted to 6PKRTSE's post in the thread Rebuilding LemonWedge. with
    Thanks!
    Thanks!
    .
    I tack welded block off panels over all of my heater blower motor, heater hose holes and any other factory holes not being used. If you...
  • malex
    malex replied to the thread Rebuilding LemonWedge..
    LW I was looking through my weight loss notes and the K-frame engine brackets that I cut off were 5Lbs plus 4 Lbs more gone by trimming...
  • malex
    malex reacted to LemonWedge's post in the thread Rebuilding LemonWedge. with
    Like
    Like
    .
    I think the motorplate is the direction we’ll be going, Malex. Yeah, this was a bad deal. I pretty much took the entire summer away...
  • malex
    malex replied to the thread Rebuilding LemonWedge..
    This is the first that I’m aware of your accident LW. Tough break. Damn. Glad that you walked away and OK. Bad news on LW though but...
  • malex
    malex reacted to dvw's post in the thread Rebuilding LemonWedge. with
    Thanks!
    Thanks!
    .
    I'd put a motor plate in it. Then any K frame will work. 6 cylinder ones are cheap. Doug
  • malex
    malex reacted to LemonWedge's post in the thread Rebuilding LemonWedge. with
    Like
    Like
    .
    Thanks…. Car was featured in a number of Calvert Suspension ads over the past few years. Made their calendar in ‘24…. The wife...
Show older items
Back
Top