• When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.

Recent content by Vincent Holt

  1. Vincent Holt

    Mystery hole in the Wall(Firewall)!

    How can you have any pudding if you don't eat jour meeat!?
  2. Vincent Holt

    Mystery hole in the Wall(Firewall)!

    Good song. My factory tach is mounted on the center console. The wire goes thru a factory hole on the passenger side.
  3. Vincent Holt

    Mystery hole in the Wall(Firewall)!

    1967 Coronet R/T 440/Auto Non-A/C Manual brakes I cant figure out what goes through this factory hole in my firewall. I've seen a single wire with large grommet on other B-bodies at car shows. I asked the owners but they didn't have a clue where it went or what it did. They must've bought not...
  4. Vincent Holt

    Trans cooler line clip..Where does it go?!

    Thanks! I'll giver a try!
  5. Vincent Holt

    Trans cooler line clip..Where does it go?!

    67 Coronet R/T Where does the clip go to hold the trans cooling lines? Looks like it attaches to the bottom left trans bolt but the lines don't jive with the location of clip. Anybody have a photo of this thing installed? I could make one but i already bought one from Inline Tube.
  6. Vincent Holt

    What size U-Joint!? Wrong parts are piling up! PROBLEM SOLVED!!!!

    All good. I only needed to it move maybe a1/16. I checked with my caliper after each turn.
  7. Vincent Holt

    What size U-Joint!? Wrong parts are piling up! PROBLEM SOLVED!!!!

    After further inspection and advice about the ear being possibly damaged... come to find out that all the ears on the driveshaft were bent! I was able to straighten them out with homemade tool. 12" piece of 3/4 all thread and grade 8 nuts with nylon inserts. I burned out the inserts for the...
  8. Vincent Holt

    What size U-Joint!? Wrong parts are piling up! PROBLEM SOLVED!!!!

    The Cross with the caps removed does not fit between the ears on the driveshaft. So Maybe each end is equally bent?
  9. Vincent Holt

    What size U-Joint!? Wrong parts are piling up! PROBLEM SOLVED!!!!

    I bought the Spicer 5-789x (7260 series) it's just a hair too big. The cross(caps removed) will not fit into the driveshaft. Also the overall size of UJ is wider than the end of driveshaft. Only bigger by maybe an 1/8" on each side. What would be the next step down??
  10. Vincent Holt

    What size U-Joint!? Wrong parts are piling up! PROBLEM SOLVED!!!!

    Definately will. I hosed it on pretty good. Thanks
  11. Vincent Holt

    What size U-Joint!? Wrong parts are piling up! PROBLEM SOLVED!!!!

    Ok kool! I'll give them a shot. Thanks for the help.
  12. Vincent Holt

    What size U-Joint!? Wrong parts are piling up! PROBLEM SOLVED!!!!

    No remains of old UJs. I chucked'em. Here are the measurements for the end of driveshaft. The length of the driveshaft is just over 51''.
  13. Vincent Holt

    What size U-Joint!? Wrong parts are piling up! PROBLEM SOLVED!!!!

    Yes, I'm aware of the trick. One of my purchase was from there
  14. Vincent Holt

    What size U-Joint!? Wrong parts are piling up! PROBLEM SOLVED!!!!

    1967 Coronet R/T. Original 440/727/8-3/4. I removed the driveshaft to replace the u joints. Both seem to be original. They u joints were very difficult to remove so they got thrown far far away. I ordered new U-J according to my make/model with all the usual sizes being listed. I have...
Back
Top