Recent content by welder47

I have both fenders, not bad shape. I did tack weld on new lowers but my body man said they are about 1/2 inch short. So a little welding is required to fix that.

The one thing I did different on my rotisserie was to make a loop on each side where the car hooks on and made a steel pulley adaptor for the top post of the rotisserie, in other words I don't use a jack I simply take my portable 110 volt winch and loop the cable over the pulley and pull the car...

Anyone find any powder paint colors anywhere that match orginal mopar colors for sale anywhere, mainly looking for oranges, barracuda red etc. Theres alot of oranges available just dont want to buy them just to see if they are close and be disapointed. Im sure one of you guys ran across matches...

Ive tried different kinds of so called black chrome powdercoat, even on chrome it does not look even close to the real black chrome. More like dark silver in my opinion. So far there isnt a powdercoat that looks right, but then again Im picky.

That car turned out great. Im going to start on my 68 charger as soon as my roadrunner is done. I do it all myself also. Was almost thinking about not doing the vinyl roof over on mine but yours looks so good I might reconsider it. Im not a 100 percent OEM guy either, I get close but I do think...

Not from chrysler, but ebay and others have the spring center parts for about 100 and up. Between what I have and the extras you can have a working suregrip for under 300.00. I have very seldom seen a rearend that inexpensive.

I recently aquired a 8 34 2881489 3.91 ratio sure grip cone type rearend center section in a pile of parts I bought. It is taken apart. The sping/ cone assembly is missing. gears are good. I dont need anoughther heavy sure grip sitting here so Im selling, someone with minor mechanical ability...

I also used the needle gun method. Most of it did fall off from the vibration, does not damage the metal either. I also used a air hammer with a blunt bit that I made. I think I did the whole underside in about 3 hours on a rotiserie. I use the needle gun for alot of stuff, works good to get...

I bet it would be about 75.00 to go that far. With a zip code I could check.

Damit Wil now I want black lol. Too bad I did all the jambs in barracuda red already. Need more pics the one isnt doing it buddy. Now your going to be all nervous putting it together without scratching it. There is a cheap roll form of floor underlayment from menards that is a good paint cover...

Yea Will your lucky that blast didnt send you over the side, the fall from those ships isnt easy to survive from. I was a destroyer guy in the navy and had a close call one night on the way to the gulf. Me and anoughther guy were on fantail watch one night, it was rough that night but didnt seem...

Strange its just one side. I have found on my stuff if I dont use a fuel pressure regulator on the carb inlet I get bad fouling from too much fuel. Most carbs dont require much fuel pressure usually abot 4 pounds, and most pumps are putting out at least nine. Edelbrock carbs are mainly what I...

They are all blasted full of undercoat now so no pics. All it took was about 8 hours with cardboard templets and crawling in and out about 200 times with the metal to make adjustments lol. And recently I took in trade a 71 Z28, 454, 5 speed hot rod as partial payment on a nova I had. So of...

I needled my splash shields also and found out the rust was just too bad and junked them. And after looking at the prices of replacements, got a headache and made my own that actually fit correctly. I always wondered who at chrysler decided to do this instead of just putting a inner wheel well...

Quarter panel for passenger side 69 RR, welds on at top of seam that runs along doors to rear light does not go up to roof support. Brand new still in box. 225.00 or offer. Part is in wi shipping would be high I would think. Also have one gallon of hemi orange basecoat and fiberglass trunk lid...