Search results

  1. K

    70 B Body Rear Glass

    Are you looking for tinted or clear? I have a clear that maybe could be buffed out? I don’t know, never removed glass scratches before, but it definitely has some
  2. K

    70 B Body Rear Glass

    I put an AMD rear glass in a 1969 a couple months ago……it fits fine, but as said before, contours are off. I had looked for a OE for a while and couldn’t find a tinted one anywhere. It’s the best option we have for now. Wouldn’t be too hard or costly to switch out later if you ever did find...
  3. K

    69 GTX taillight bezel restoration?

    Yes Calling him will save you a few bucks on shipping versus ordering from his website.
  4. K

    69 GTX taillight bezel restoration?

    As boss302 says, careful taping off of chrome and surface prep is key. I lightly blasted all areas that needed paint. My chrome is not nearly as nice, but the painted parts came out great. 877 paints has exact paints and textures. I highly recommend calling him and he will walk you through...
  5. K

    WTB 1969 4 speed console molding Left side

    I see that Brewer’s sells the right side separately, but not the left????
  6. K

    WTB 1969 4 speed console molding Left side

    Looking for the stainless moulding that goes on the 4 speed console for a 1969 Sport Satellite. I only need the left side. Thanks for looking!
  7. K

    FOR SALE 1969 1970 4 speed console shifter center plate.

    Rob, I’m waiting for your PayPal info but realized my inbox is full, ….can’t figure out how to delete messages, but I’ll keep trying.
  8. K

    WOM or not?

    Wow! Great looking car….definitely better with them on. You have all convinced me. I appreciate Eldubb letting me know the OER trims fit good, but I ordered an AMD set last night, so I will let you all know how they fit…..hopefully soon!
  9. K

    Carb Choice for Stock 440?

    I am in a very similiar situation, except I still have stock intake and heads. I had a edelbrock 1406 (600cfm) for a short time that would stumble on hard acceleration. I switched to a Holley 3310 and think it runs great! Good power with no hiccups or starving for fuel, and very smooth and...
  10. K

    WOM or not?

    Thanks, I see that Classic Industries sells OER moldings, and AMD looks to have sell their own ones. The mouldings originally on my car are anodized aluminum. Should they have been stainless steel? The moldings for the Charger specifically say stainless steel, but descriptions for the...
  11. K

    WOM or not?

    Can’t decide if I should put wheel opening moundings back on or not. My originals are too far gone, so I would be looking at repops. Can anyone tell me how the repops fit? I have tried to reuse as many original parts as I can because I have been disappointed with most reproduced parts thus...
  12. K

    Any good alignment shops in Phoenix, AZ?

    Thanks Dryheat, I appreciate the recommendation
  13. K

    Any good alignment shops in Phoenix, AZ?

    Anyone know of a good place to get a wheel alignment done on one of these old cars is the Phoenix/Scottsdale area? I took it to one today and could barely drive it home it pulled so hard to the right! It drove almost perfectly going there, but took it in anyways to have itchecked out by...
  14. K

    installing bolt in shifter handle in push in box

    I ran across the same hurdle recently……called Brewers, they sent me out a couple pieces to convert my existing shift mechanism, took 10 min and maybe cost $30. Much easier then drilling your old one if you ask me.
  15. K

    How cheap are the cheapest Challenger Hellcats now?

    Although not a Hellcat, I picked up a new Scat Pack, manual trans, for $6400 below MSRP last week. I like the old mopars as well, but these new cars are insanely fun and comfortable and powerful! Best decision I’ve made in a while. I know it is a big step down from the Hellcat, but for the...
  16. K

    Which electronic ignition

    Switched from points to pertronix II in stock distributor and flame thrower coil. Couldn’t be happier and very simple to install! I am finishing up the interior of the car still, so not a lot of miles on it yet, but seems like a great improvement so far…..cars runs smoother and seems more...
  17. K

    Check for exhaust leaks by pressurizing?

    Wouldn’t you need an intake valve open for this to be an issue? Not sure how you would have an intake and exhaust valve both open on same cylinder at same time? Maybe this isn’t the best way to check for leaks, but like I said, I thought the concept was intriguing. It’s pretty tight and hot...
Top