Search results

  1. M

    Header gaskets or no?

    Can you reuse a exhaust gasket, about 6 months old?
  2. M

    Edlebrock RPM Heads on Stock Engine Questions

    Well I'm hoping these heads will increase compression so that won't be an issue. Anyone else have thoughts on this?
  3. M

    Edlebrock RPM Heads on Stock Engine Questions

    Fel Pro 1009 - .39 Edelbrock 7325 - .38 .01 - Probably not a noticeable difference. Anything if the stock distributor will fit with these heads?
  4. M

    Edlebrock RPM Heads on Stock Engine Questions

    Yes, I am. I'm having them shipped directly to them, mild porting done too.
  5. M

    Edlebrock RPM Heads on Stock Engine Questions

    Another good question? IDK? I was looking at these. 440 Source actully pointed these out to me for their Stealth Heads that I decided not to get. //www.hughesengines.com/Index/products.php?browse=search&search=5983&partid=28510
  6. M

    Edlebrock RPM Heads on Stock Engine Questions

    I don't even know. It was hard for me to see the casting #'s. I think it actually said 74, and it's in a 1972 Satellite. What do you mean? "And almost certainly not with most stock 400 cam timing."
  7. M

    Edlebrock RPM Heads on Stock Engine Questions

    75CC I goal is to lower the compression. Since the 400 is a low compression Engine I figured the Piston to Valve clearance wouldn't be an issue. I just just reading that the valves are bigger than the stock valves and that's where the problem could come in. I hope the headers work. Don't...
  8. M

    Edlebrock RPM Heads on Stock Engine Questions

    Hello, I just purchased RPM heads... One of the things mentioned is to check the Valve to piston clearance. Should I be good with a stock 400? Also... is there an issue with using the stock distributor? Will the heads fit around it? Can I go with a thinner head gasket of .22 ? Can I still use...
  9. M

    Can someone guide me for a proper cam?

    With the RPM heads, can I use the stock rockers and push rods? I may hold off on the cam for now.
  10. M

    Need Engine Builder/Machine shop in Northern Milwaukee

    I've called a few places in Ozaukee County and no one seems to answer the phone or calls back. If someone could guide me to a reputable shop I'd appreciate it!! Thanks!
  11. M

    Can someone guide me for a proper cam?

    The Lunati specs called out for a 800 Cfm.
  12. M

    Can someone guide me for a proper cam?

    HI, I'm back... I talked to the guy from 440 Source. I guess the Stealth Heads are 80CC... So in the middle of the two Edelbrock heads. For $599.00 Each it's tempting. Anyone like these heads? "Single with Damper. Recommended for maximum .510" lift" Also looking at COMP Cams Camshaft...
  13. M

    Car just died and won't start?

    Lol! I just looked at the choke, it was stuck closed! Sorry for freaking out guys!
  14. M

    Car just died and won't start?

    Well... I gave it a lot of gas and it started again, but chugging really hard!
  15. M

    Car just died and won't start?

    My car was running perfect, I was at a stop light then when it turned green I stepped on the gas and there was a poof sound and it seemed to be running on 1 cylinder (uphill of course) i got it on a side street and shut it down. Now it won't start at all. Any ideas what it could be...
  16. M

    Can someone guide me for a proper cam?

    Would I get 1.5 or 1.6 rockers? (getting closer guys!)
  17. M

    Can someone guide me for a proper cam?

    Well, I'm still looking into the Whiplash Cam, I have sent them an e-mail. Or I'd go with what is recommended above Lunati voodoo 703 226/234@.050. Not sure If I can still use stock rockers on either cam?
  18. M

    Can someone guide me for a proper cam?

    Thanks!!!! You guys are the best! And I would need new Rocker arms I assume. Stock wont work with any aftermarket cam? What kind of Rocker Arm set up can I get away with that wont break the bank?
  19. M

    Can someone guide me for a proper cam?

    Can I get more info on a torque converter? "9 1/2" ptc or dynamic. One that flashes 4000+ but cruises like stock." What would that be? Is the 400 internally balanced?
Top