Search results for query: *

I’m wondering if my OER tic toc tach (69 Bee) is causing my no spark issue and curious if I have it hooked up correctly. The gray tach wire is going to upper terminal and red wire to bottom terminal. Not sure if I labeled the back correctly, so disregard my notes on tach back. The clock works...

Recently installed my 440 engine, that ran properly last year. Was pulled to fix an oil leak. (Car is running Mopar electronic ignition conversion and has been issue free for years). Now, when trying to start, I have no spark from coil, based on coil test lead plug grounded to chassis. When...

FBO distributor limiting plate. Never used. 0-10-12-14-16-18* Mechanical Timing limits This FBO Advance limiter plate will allow you to have the limiting abilities of a Mopar Performance Distributor in minutes. Quick easy and changeable as your engine performance level changes. One Simple...

Beautiful Glasstek hood installed. Was way easier than I thought, especially after measuring 5 times and drilling once. Now for paint and final brackets install/tightening.

Are the rear mounting plates supposed to be at a slight angle upward or should they be level ? With them leaning, the pins lean too.

Does anyone have under-hood pics of the hood pin mounting hardware. Curious what the hardware looks like underneath and if the rivets go all the way through. I’m assuming pilot holes need to be drilled for the rivets.

NIB Fel Pro valley pan kit #1215 for big blocks except Max Wedge. $28 shipped to lower 48 states. PayPal, money order, or cash if local to NW Indiana accepted. PM if interested

Anyone know if just this plug is available, the black casing? For a 69 Coronet rallye gauge.

Looking for this headlight switch plug for 69 Coronet rallye gauge PM please

The fitting going from the stock trans cooler line to the AN fitting that allows the AN fitted lines to be attached? It’s been flawless and leak free so I’m thinking to use a similar fitting for my 3/8 factory fuel line to an AN line to a fuel pressure regulator with return line.

FBO distributor limiting plate. Never used. 0-10-12-14-16-18* Mechanical Timing limits This FBO Advance limiter plate will allow you to have the limiting abilities of a Mopar Performance Distributor in minutes. Quick easy and changeable as your engine performance level changes. One Simple...

Used Layson’s vapor separator with 3/8” fuel pump line. 3/8” in, 5/16” out, and 1/4” return fitting. $25 shipped within continental US, or $20 if close to NW Indiana and picked up. PayPal, money order, or cash accepted. PM if interested.

Brand new, never used, still with packaging. 3/8” in, 5/16” out, and 1/4” return fitting. $35 shipped within continental US, or $28 if close to NW Indiana and picked up. PayPal, money order, or cash accepted. PM if interested.

Brand new, never used. $27 shipped within continental US, or $20 if close to NW Indiana and picked up. PayPal, money order or cash accepted. PM if interested

Brand new, never used. 9/16” size. $20 shipped within continental US, or $15 if close to NW Indiana and picked up. PayPal, money order or cash accepted.

PST Fast ratio steering arms, brand new, never used. For pre-73 cars. $120 shipped within continental US, or $110 if close to NW Indiana and picked up. PayPal, money order or cash accepted. PM if interested

Dana 60 adjustable pinion snubber. $55 shipped within continental US, or $50 picked up if close to NW Indiana. PayPal, money order, or cash accepted. PM if interested.

I’m assuming the intake valves should NOT look like this, with gunk built up on them. Looks like I have oil leaking in there, and probably confirmed by the wet blackish film in intake runner.

for those who know, does OER’s Tic Toc Tach have the continuous quartz movement or does the second hand tic? My tic toc tach is no longer the original and because I disconnect the battery when not in use, the tic toc second hand has stopped working and I’m trying to figure out if it’s cheaper...

Is this little hole in the temp gauge for adjustment purposes? There’s a brass tab right behind the hole that connects to the brass strip going to the temp needle.