Search results for query: *

Hi Guys, I am looking for the bolt that holds the Air-Grabber actuator in adjustment. It has a 3/8 head, 3/8" long, 12-24 threads, and a washer that is a little more than 1/2" in diameter. What is on the head...I do not know. I attached puctures, so if you know what the markings are, please...

Hi Guys, I am looking for one or two of the screws that hold the seal to the bottom of the air-grabber box. It has a 5/16 head, 3/4" long, and a roughly 3/4" diameter washer. The head has an AF or F on it. I have not figured out which it is. Does anyone have any extras laying around? PM me...

I started putting some real time into getting things together to get my rear end, front suspension, and other small components together so that it us ready to put on the GTX.

What are you guys using to replace the foam seal that is on the front backing plates for drum brakes? Do you just jam foam in there and trim it out or?

Guys, I am restoring my original parts for my Air Grabber (70 GTX). Does anyone know what finish is supposed to be on these parts? I have scrubbed down through and found what looks to be like yellow-gold cadmium plating in two of the parts. Is this correct or not?

WTB: 11" x 2 1/2" DRIVER'S side Dana 60 or 8 3/4 backing plate. Must be pit free. PM me here. Thanks

WTB - Looking for a set of 70 Hemi Leaf Springs for a B-body. I think they are 3004-767 & 3004-768. If I am wrong on those numbers please correct me. PM me here. Thanks, Tom

Ok guys, which is the correct strap for a 70 GTX from Lynchroad? I have 2 different styles of straps. As you can see one style is straight and the other lays to the one side.

Looking for cover bolts for a 69 or 70 Dana 60. PM me here.

Looking for a set of pit - free 11" Rear backing plates for a 68 - 70 B body. They must be pit free. What's out there? Pm me here. Thanks for the ad.

Looking for bolts that hold the seat tracks to the bottom of the seat in a 70 B body. There are 8 bolts total. Also I need 1 (one) bolt (stud) for the bottom of the seat track that goes through the floor for a bucket seat bracket. I don't know, they may all be the same. What does anyone...

Guys, I tore into the taillights for my 70 GTX. I wanted to clean them up and get them ready for installation. When I washed the housings, the silver coating inside the light area washed off. I was kind of in shock, but I guess after 54 years, parts lose thing also. My question is this, what...

What product do you guys use to re-coat the "rubber or plastic" ends of the wiring harness clamps/clips that are welded to the body? Or where do you get repop ones? Thanks, Tom

Guys, I'm looking for two of the "clips" or "mounting clips" that slide over the bracket that is welded to the bottom of the door where the bottom adjuster for the vent window frame goes through and is tightened down. It is a square piece (approximately 2" square) that is bent over it's self...

For Sale: 1970 Dodge Color and Upholstery dealer wall chart. When was the last time you saw one of these for sale? You can check it out at Carlisle. Spaces N19 - N21. This chart is approximately 5' long x 3.5' high. It has the original masonite mounting board with the flip up sides to change out...

Wanted: Rear spring shackles for 70 Road Runner / GTX. Very nice to mint or NOS only. Preferably complete with nuts. PM me here. Thanks!

Hello everyone, I am looking for the original 426 Hemi engine and 4 speed transmission for my 70 GTX. The last 4 numbers on the pads should be 4378. The car originated in Georgetown, DE. It is B5/B5. I thought I had a line on the transmission being put in a 69 Road Runner in the Maryland area...

I guess I should have been more specific in my request for measurements of the hood pin holes for my hood. Could someone who has a hood with factory hood pins from a 70 Road Runner / GTX that was built at the Lynch Rd. plant please measure the diameter of the hood pin hole drilled in the hood...

Hello, What size are the holes that are drilled in the hood where the hood pins go through? Also, what size are the holes for the screws for the plate that screw to the hood? Thanks!

Hello all, A little while back I was looking for the nut for the hood bumper on a 70 GTX. Someone on here was nice enough to send me one free of charge. An NOS one at that. I am greatful to them! My question / concern / problem is this: My NOS fender has the rectangular nut welded on to...