Search results for query: *

im heading down to the moparty in the morning. Is there an FBBO members tent or anything? Looking forward to meeting some members there. 70rrclone.

Original bumpers from my 70 satellite. They are cores and will need straightened and rechromed. $100.00 each plus shipping i can deliver to the moparty for 50% deposit.

MSD Starter pn 50982. Used for Break in only. Fits the hooker 2in 5209 headers used during break in. Will not fit with the 2in TTI headers in the car.. $275.00 plus shipping or can be delivered to the moparty with 50% deposit

70 plymouth B Body passenger front fender. It has had a poorly done repair on the wheel opening roughly at the 1 o'clock position. Its not perfect but not rusted junk either. $500.00. Can deliver to the moparty with 50% deposit.

Im thinking im pretty lean buy the way the plugs look. This is after I got home frome a 300 mile round trip. They are lighter in person than the pic. Im kinda surprised by the plugs. I thought an 850 would be overkill for a warmed 440. Engine specs 440 wiseco pistons 9.84:1 Comp xe285hl .545...

Has anyone used the OER door glass for 68-70 B body? Can someone tell me how thick it is? Thanks DD4258T - 1968-70 Dodge, Plymouth B-Body; Door Window Glass; 2 door Hardtop; Tinted; RH Passenger Side

I am looking for a set of 12 s shaped roof rail trim clips for a 70 Satellite. Thanks Shane

I had a leak and needed to pull the center section out. How does this gear pattern look. It's only got about 50 miles on it. The backlash is right at .010. It seems noisy to me especially coasting in neutral. And the pinion seal is leaking. :mad: Should I make any adjustments while its out...

I put a tf2 shift kit in my 78 727 trans and now it won't upshift. First and reverse work. And the trans worked before the kit. Max tv press is 130 Line press is 90 stall and 75 at 1k idle Rev servo press is 200 stall and 160 1k idle Low gear has 50 measured at the rev servo Gov press was 65...

I have a noise in the valvetrain I can't find. I have the drivers side rockers off looking and noticed the exhaust valves have the roller markes a little below center and about .050 wide. The intake roller marks are all over the place. Looks like the intake valves are spinning. I'm running a...

Does anyone have a source for the bullet connectors to rebuild the ignition switch and turn signal plugs? Thanks

Looking for a pair of front spring hangars with stock and lowered height holes for a 70 satellite. Likes these

I'm looking for 2 windshield interior trim clips like the ones pictured. There for a 70 satellite. Thanks Shane

So, im curious. What are the horsepower/torque estimates for my 440 are. Dynosim 6 say 590 but I think that's quite high. I'm thinking closer to 500-525. So what's your thoughts? Thanks! 77 440. Wiesco pistons measured 9.84:1. Trick flow 240 heads 1.6 mancini rockers Comp xe 285hl cam.. .545...

I bought these exterior door handles from Detroit Muscle at the Nats. Somehow managed to buy the wrong pair. These have the black push button. Still in the DMT package. $90.00 shipped in the lower 48.

My car seems to have very high rolling resistance. I can barely push it in and out of the garage in neutral. After ruling out dragging brakes and disconnecting the drive shaft, it seems the 3rd member is very tight. I noticed it was very hard to turn by hand before i put it in the car. But...

I need a left and right door handle latch links. From the door handle to the latch Thanks

Is anyone going to the streetrod nationals in Louisville? Im hoping to have my car assembled enough to take it this year.

I finally have my car painted and cleared. I put about 3/4 of a gallon of clear on the outside not including the hood.(jams were already done). At this point there is some dust in the clear which i expected doing this in my garage. Should i cut and buff the dust out now? How do i tell if i have...

Im looking for a ralley cluster lens for a 70 roadrunner. I dont need a whole cluster just the lens. Thanks Shane