Search results for query: *

So I have the repop bezels I am using on my GTX. I have some older nuts removed from the original bezels. I also purchased new nuts that are for a 70-71 Challenger. Does anyone know if these will work or should I just clean up the old ones and reuse? Also, is there a trick to keep the bezels...

I have a set of the top door edge moldings off my 71 GTX I am not going to use. These are the thick wide ones that set on top of the door and the quarter. the quarter ones are shaped like a C. These are usually pared with the roof edge moldings. I have a full set plus a few extra pieces. I...

Looking for definitive information on how the rocker moldings attach. I have heard some say just screws in the holes and some say clips. I have a set I am going to put on my 71. Holes are there in the body but no idea other than screws how they would attach. If they were flimsy chrome pieces...

looks like at sometime I must have misplaced the e-brake lamp switch for my car. Looking to see if anyone has a good switch they would part with before I end up buying a whole assembly to just get a switch. Let me know Thanks!!!!!

I was looking to see if someone can tell me or show me where the metal wire supports go in the inter behind the dash for the 71 model Plymouth B body. I am referring to the sheet metal brackets the part of it looks like it dipped in plastic or rubber and it holds or supports wires. Thanks! Ben

I am working on installing new brackets for a manual trans console. I was wondering if anyone had templates or pictures with dimensions for the bracket locations. Any help would be appreciated. I almost forgot to mention that I am working on a 71 GTX.

Looking for a passenger door skin for my 71 GTX. Closer to Indianapolis the better.

I am currently converting a Satellite hood to an air grabber hood for my 71 GTX. I found the template for whole locations, but I am looking for an image of how much the front brace gets trimmed as well as other inside modifications for the hood to allow it to look somewhat correct. I know I...

Looking to see what’s out there. No preference in complete or partial assembly or ratio. Ty. Ben

Looking for a 71 or 2 Plymouth B body trunk lid. Looking specifically for one in good shape that has the cut-outs for the trunk spoiler. Let me know what you have and what you are asking for it.

So I am in the process of working on the quarter windows for my 71 GTX. I notice the on two of the black guide blocks that there is a small spring that keep tension in it while running up and down the track. Are these black guide blocks available? Also what about the small tension springs? Last...

Maybe not the right spot to post this, but I was checking to see what the going rate one would pay for a used front 71 RR/GTX/Satellite bumper that has no dents or dings. Chrome will need cleaned up and the bumper bolt holes are all in good shape. It does have some surface rust on the back...

Looking to see if anyone is parting out a Satellite/RR/ or GTX. I am looking for an upper cowl panel and potentially the bottom 6” of the a-pillars. Ben

Short of finding two a pillars to cut patches out of,does anyone know if the e body lower corner patches that are made would work? Ben

What are you using or do you guys recommend for the thin strip of rubber that holds the quarter glass in the bottom and the front chrome strip? Ben

So is there a trick to getting the front edge chrome off? I know there is a little screw at the bottom other than that is it just slid on or do I need to remove what like a river at the bottom of it?

Anyone know of a source for tall style Pal nuts used to hold the bezels on the marker lights for these cars? Seems to be a few different ones for the E-body's? Also, several of mine are bent from over tightening. Has anyone or is there any tips out there for straightening these? Ben

Mac's engine lift pivot plate for sale. Used once. This is the base plate. There are many attachments available to use with this if you are a GM or Ford guys as well. I used this once for the my GTX. I was able to pull motor and trans with the radiator out in my car. I am not going to need...

Hello I am looking to see if anyone has a clear picture of the what the area looks like where the cowl panel top meets the corner of the A pillar for a 71 RR/GTX/ Satellite. I have some rot in the corner and was needing a clearer picture of what I need to actually repair. Thanks in advance. Ben

I have 12 leaf spring pads and 2 liners left over from rebuilding my springs. I don’t need them so $30 shipped in the 48. PayPal ok if you pay the fees. These are from ESPO and worked well for my springs for my GTX. Ben