Search results for query: *

Anyone have a set of 15x8 steelies that allow for the 10" cap? Or a set of the early 15x5 steelies that allow for the 10" cap? Casey FJ

Need some help. Looking to put the stock 10" poverty caps off of my 14" rims onto a 15" steel factory looking wheel. I have a set of factory mopar steel wheels, but of course they accept the 9" cap. Any idea where I can get this wheel? Coker's show they have steelies to fit the 9" but no 10"...

Looking for a solid street/strip low deck engine. Will buy complete/ long block/ short block Must be pump gas friendly. 470/500/512 The closer to Columbus, OH the better Thanks, Casey FJ

Good Afternoon, I am looking for a decent set bumpers (steel) for a 65 dodge coronet (front & rear). Also a complete hood latch assembly for a 65 coronet. Thank you, Casey FJ

Looking for a GOOD 400, bare, unmachined block. Steel 383 standard crankshaft. The closer to Ohio the better! Thank you, Casey FJ

Looking for a set of small valve big block 915 heads in good shape! Will be going in a stock eliminator care, so they cannot be ported/ big valves. The closer to Ohio the better or must be willing to ship! Thank you, Casey FJ

Koffels Place Built 549” B1 Originals ported by Koffels Place T&D Shaft Rockers Manley Stainless Valves Titainium Retainers KB Block - Never Windowed 13.65:1 Motor Wiseco Pistons BME Rods Moldex Crank Jesel Belt Drive Comp Cam - .820 lift Highly Modified Indy Bathtub Intake for B1 heads Two...

Looking for complete Carter 3860S carbs. Stock eliminator build. Thank you,

1966 Dodge Coronet Street/ Strip Car - Just a carb change to be Nostalgia Super Stock legal - 540” Mega Block/ Callie’s Crank/ Callie’s Rods/ Diamond Pistons/ 13:1 / Stage 6 Heads/ Harland Sharp Rockers/ Super Victor Single 4/ QFT FX-4700 dominator/ Super Comp headers with bullet mufflers/...

Looking for a good 62 Plymouth hood. Not worried about trim or paint just need a solid hood. Current hood someone hit with a bit too much pressure on the sand blaster… Closer to Ohio the better. Thank you!

Looking for a 1965 Coronet Wagon! Project, driver, built.. What do you have out there! Casey FJ

Looking to buy a 65 Coronet Wagon only. Looking for a project or complete. Not looking for a rusted out shell. Thank you! Casey Fauss-Johnson

8 3/4 Pumpkin 742 case Suregrip 5.12 gears Small yoke $550 obo Pinion Snubber $25obo Shock plates $40 obo Located in Blacklick, OH Can deliver to the Nats

1962 Dodge Dart 330 Wagon Great patina, some rust but overall solid and complete! 225ci slant 6 Push button auto Rebuilt Holley 1920 Mini starter Brakes redone Keystone classics with great tires Complete front and back bench seat- both need recovered New carpet - not installed New...

What is out there?! Must be a 4 speed 62-67 Plymouth or dodge Big block Not looking for a big project.

Looking for the horn retainer ring for a 62 dodge steering wheel. thank you

Good Afternoon, Looking for a 63-65 K frame to swap into my 62. Big Block motor plates are a plus! Closer to Columbus, OH the better. Thank you, Casey FJ

Hey Everyone, Just bought a 62 Dart wagon.. looking to swap out the slant with a 440 and a 727 push button. This is a street/ budget build.. Sooo.. are there conversion mounts out there for such a beast? Is my only option switching out the K frame and components? Do I just use a motor...

Does anyone know if there is a source for interior parts for a wagon? Carpet Headliner Door panels - Are these the same as a 4 door? Seats Thank you

Looking for a 62-67 station wagon. Driver quality Prefer a 3 on the tree. Closer to Ohio the better but will travel! Cash in hand