Search results for query: *

I need to get the wheel off to replace the turn signal switch. Dang, what's the trick. I have twisted and pulled and I don't want to break it. The bar across the middle is separate from the horn ring of course.

The channel on the back side of the vent window frame that the door glass slides up and down in is gone on my car. There is no weatherstrip there and of course it leaks and rattles. I think I just need window chanel from what I see in a catalog. I searched around the site and read threads about...

Like the title says, If you are looking for a new part, a used part, or who sells repopped parts, you must start a Parts Wanted ad in the Marketplace forums. We give latitude for comments in most wanted ads so suggestions are allowed. If you post your parts needs in the wrong forum (non sale or...

I have been told my drivers side brake lights don't work at times. Also my turn signal switch is wonky, not smooth and it doesn't cancel when turning right at times. Tonight when I put it in the garage and closed the door, I stepped on the brakes and sure enough the left lights didn't light...

I got a nice 7503 with my Polara and because of my fuel/carb issues lately, I'm seriously thinking about installing it along with an Edelbrock 650 AVS II carb which I also have. How does your combination work? Any loss of bottom end because it's an open plenum intake? Are there any crazy things...

I think mine are 15X7 standard offset Cragars with a 245/60 but it looks like a 10" wide and a bigger tire would fit without rubbing. I like a big tire on the rear.

When I start the car, the steering wheel will turn to the right a 1/4 turn. I also had a pull to the right. I just got the front end aligned and when it was on the rack (turntables) you could start the car and it would turn to the right all the way without touching the wheel. I have read about a...

If you request parts anywhere other than in a proper Parts Wanted ad, in the Marketplace forums, your post and/or thread will be deleted. Also, if a member is asking for what parts may fit and you offer any parts, Your post will be deleted. Don't mess it up for the guy. Many members go right...

I need to figure something out. I am just shy of 6' tall but my seat needs to go back further. It is as far back as it will go adjustment wise. I am setting pretty close to the steering wheel. Both the wheel and the seats are factory issued as far as I can tell. I haven't looked underneath to...

I've descovered I have 2 left hand headlight buckets and need a correct right side one for my 64 Polara The indent to locate the headlight bulb should be at the bottom. It's not. LOL Pm me with what you have. The adjusting hardware would be a plus. Thanks.

Here's the schematic I used to get my 64 starting and running right. The previous owner had it basically wired like this but had installed a 5 pin ECU (for a dual ballast system) and the only way it would start is if you jumped the + side of the coil with 12 v. from the battery. He didn't use a...

I was poking around on the net and checked into this site. Here's some history about the Ramchargers, their program, and some great old photos. https://www.ramchargers.com/index.php/history

I just got my dash pad in from ABC Moparts. It looks real nice. Did you guys use the wire door panel clips or did you try some plastic Christmas Tree clips? I used those for under hood insulation on my Swinger and they really worked well. Easy to install for sure.

Not only is it against the rules, the scammers would love to know who you are and where you live. No names and addresses, E-mail addresses, Pay Pal information, bank info, or the like. If We see it we will immediately delete it and you will have to start over. Send it safely through a...

Are there any companies out there that have pads for these old girls? Mine came without a pad. I see Herbs has them listed Herb's Parts: 1965 B Body Dash Pad NEW, Dash Pads, 65RWDASHPAD. or would it be best to find a core and have it redone? I see the applications are for 64 Polara and 65...

I am looking at a 64 Polara and I see it has new exhaust on it. I haven't seen it from underneath so I don't know much about it yet. I did see the tail pipe tips come straight out under the bumper. I looked through a couple hundred photos and saw that the tips are supposed to be turndowns which...

I found a 64 Polara and although it's a Az. car I wouldn't mind finding out the bad spots for rust and the like. It was painted 10 or so years ago so it probably has some filler. Thanks.

@LocuMob passed away after Christmas. I just heard tonight. Scott will be missed. He was an active member on A and C Bodies as well as Trucks. Here's Scott on the right and 66340sedan (Keith) from FABO on the left. USER=1]@Joeychgo[/USER]

After the block casting number is a -3. What does that stand for. I always thought it was revisions to the mold yet I hear someone else said it's the pours out of the same ladle at the foundry. (I doubt)